爐前高精度鋼鐵水熔煉爐鋼水，鐵水，銅水鋅水微機智能測溫儀型鋼水鐵水銅水測溫儀無線測溫儀AN200型鋼水鐵水銅水測溫儀

1 簡介
本測溫儀以高速16位嵌入式微處理器為核心。采用了自動校準電路，采用精密的溫度傳感器對冷端溫度進行測量，并可以進行軟件校正。在數據采集上采用高精度AD轉換芯片，采樣周期為20ms，對空間的工頻有很強的抗干擾性。
本測溫儀可適用于煉鋼、煉鋁、鑄鐵等行業中溶液溫度的測量，也可以測量爐渣溫度。
2 功能說明
? DC12V有源喇叭輸出接口√
? RS485串行通訊接口（訂貨特殊說明）
? 微型打印機接口（訂貨特殊說明）
? RS232異步串行通訊接口（訂貨特殊說明）
? 帶隔離的BCD碼輸出接口（訂貨特殊說明）
? 模擬量4~20mA輸出接口（訂貨特殊說明）√
? 30條歷史測試數據存儲（如需存儲更多得歷史測試數據，訂貨時特殊說明）√
? 語音報數（訂貨特殊說明）
3 技術參數
熱電偶型號 S B R WRe3/25
快速測溫范圍 1000~1769℃ 1000~1820℃ 1000~1769℃ 1000~1999℃
連續測溫范圍 100~1769℃ 500~1820℃ 100~1769℃ 100~1999℃
顯示方式 3位半5英寸高亮度紅色LED，字高127mm
工作環境 溫度0~55℃；相對濕度<85%
存儲環境 溫度-40~85℃；相對濕度<95%
電源 AC220V/50Hz，功耗20W
尺寸 400mm×300mm×110mm

精煉爐專用大屏幕微機鋼水測溫儀高溫2000度銅水，鋼水液體廠家

1 Introduction

The temperature measuring instrument with high speed 16 bit embedded microprocessor core. Using the automatic calibration circuit, using the measurement of the temperature of cold end temperature sensor precision, and can be a software correction. Using high precision AD conversion chip in data acquisition, the sampling period is 20ms, the frequency of space has very strong anti interference.

Measurement of the temperature measuring instrument can be applied to the solution temperature, aluminum, cast iron steel industry, also can measure the temperature of slag.

2 Function

? DC12V speaker output interface√

? RS485 Serial communication interface（When ordering special instructions）

? miniature printer interface（When ordering special instructions）

? RS485 Serial communication interface（When ordering special instructions）

? An output interface of BCD code is with isolation（When ordering special instructions）

? the analog 4~20mA output interface（When ordering special instructions）

? the 200 historical test data storage√

? Be speech sound（When ordering special instructions）

3 Technical parameters

4 Panel

The panel is provided with a three measurement indicator: preparation, measurement, end, and three key：K1、K2 and K3。

5 Indicator lights and alarm horn control output instructions

In the absence of measurement is not yet inserted thermocouple temperature measurement instrument, display the current time, the three lights are not bright, insert the thermocouple after the green light, the thermocouple is inserted into the molten steel after the yellow light, when measured after the success of the red light, at the same time the alarm output control.

After testing the test results show that 180 minutes 5 seconds, horn, trumpet for active DC12V output. Schematic wiring as shown below:

6 Set key and dial the specific operating instructions

There are three key K1, K2 and K3 in the thermometer on the front panel is used to set the date, time and operation parameters. The K1 key is used to select parameters to set (the specific item number shown in the table below), the K2 is used to select the set position, K3 is used to input a specific parameter value.