s are mainly used in the field of water supply and sewage treatment. It is a polymer coagulant added to wastewater. After the polymer coagulant dissolves, the polymer is formed.
The structure of polymer is a linear structure. One end of the line pulls out a tiny particle, the other pulls out another tiny particle, and acts as a bridge between two distant particles, which gradually enlarges the particle # and eventually forms a large 聚合氯化鋁的水不溶可以通過溶解聚合氯化鋁來觀察。一般情況下聚合氯化鋁溶解后的水溶液較為渾濁時，就表示聚合氯化鋁中的水不溶物較多，反之溶解后的聚合氯化鋁水溶液越清澈，就表示聚合氯化鋁中的水不溶物含量越低。需要注意的是，聚合氯化鋁在固體狀態下很難直接分辨聚合氯化鋁中水不溶物的情況。
。聚合氯化鋁的水不溶物一般是由于生產原料和生產工藝決定的construction, and do not pollute building water.
污水處理廠常用的外部碳源是甲醇，工業葡萄糖等。甲醇應該是最理想的反硝化補充碳源，但其高成本，高毒性和運輸困難逐漸被其他產品所取代。工業葡萄糖通常用作額外的碳源。過程測試水質呼和浩特市水處理解答處理污水加多少聚丙烯酰胺效果好？
聚丙烯酰胺廠家處理一噸的污水用聚丙烯酰胺，通常用量是7- 10克，一般是2~4克，出現差別主要是pam的質量不一樣，或者是投加的方式不對，不然就是這個 產品跟污水的型號不配套導致的。 質量好的聚丙烯酰胺添加量少，次一點的添加量稍微多些，具體點介紹就是1-3克左右，呼和浩特市符合一般的市政廢水，工業廢水略高，3-6克左右，的10克的也有。How much polyacrylamide can be added to the wastewater treatment solution in Hohhot?
The amount of polyacrylamide used by polyacrylamide manufacturers to treat a ton of wastewater is usually 7-10 grams, usually 2-4 gram象的根本原因是聚合氯化鋁在水處理領域具有獨特的優勢。
聚合氯化鋁PAC處理后的水鋁含量很低，這也是目前PAC在飲用水處理中最常用的主要因素之一。此外，優質飲用水級PAC使處理后的水更加安全。聚合氯化鋁且腐蝕性較小。在實際生產和使用中，操作簡單，水處理效率高。聚合氯化鋁結合各種特性已成為主s. The main difference is that the quality of PAM is not the same, or the way of adding it is not right, otherwise the product is not matched with the type of wastewater. The quantity of polyacrylamide with good quality is less, and the amount of polyacrylamide with minor addition is slightly more. The specific point is about 1-3 grams. Hohhot City accords with the general municipal wastewater. The industrial wastewater is slightly higher, about 3-6 grams, and the highest 10 grams are also available.
Our answer is only a rough estimate and a budget, but the exact amount should be calculated according to the actual object. The technology will compose 0.1-0.5% solution, and then determine the project dosage in a small scale. Four-thousandths of the 1,200-15 million parts of polyacrylamide wastewater treatment will be compounded with 7-10 grams of monosodium glutamate per ton, layer slag of brewery, wastewater and so on. We can see from the above, in addition to the help of manufacturers to choose polyacrylamide, when using their own, we should pay attention to the use of polyacrylamide. Let's simply remember the following points. Dissolution equipment is required. Concentration should not exceed five thousandths when dissolving. If the equipment is a very simple dissolving pot, we should pay attention to adding 20% of the volume of water in the tank first, then polyacrylamide and water into the tank at the same time, and polyacrylamide should be poured into the tank at a uniform speed, not too much at one time. Otherwise, fish eyes and other phenomena will occur.
我們的回答只是個大概和預算，具體多少還 是要根據具體的實物來測算。技術會配成0.1~0.5%溶液，然后小試確定工程用量，聚丙烯酰胺的污水處理1200-1500萬千分之四配每噸用7-10克味精、啤酒廠 層渣、廢水等。我們從上面看出，除了廠家幫忙選購聚丙烯酰胺，自己在使用時候，要注意聚丙烯酰胺的使用方法。我們只要簡單的記住以 下幾點。要有溶藥設備。在溶解的時候濃度設定不要超過千分之五。如果設備是很簡易的溶藥罐的話，要注意在人工加藥時，要先加20%罐體積的水，然后聚丙烯酰胺和水同時進罐，并且聚丙烯酰胺要勻速的向里面傾倒，不要一次性加的太多。否則會產生魚眼等現象
測試中心在工業葡萄糖成分的測量和計算方面做得很好。在實
