特點：<\/strong><\/span><\/span> <\/p> 1、AC0～<\/span>5.0A<\/span>交流電流互感器專用接口，反時限交流過流保護停機功能。<\/span><\/span> <\/p> 2、DC148V非隔離直流高壓電壓反饋信號專用接口，用于直流高電壓反饋輸入。此功能應用時，請采用安全有效的控制方案，確保人身與設備安全！！<\/span> <\/p> 3、外部緊急保護停機信號專用接口，可用于設備過溫保護、緊急停機等。<\/span><\/span> <\/p> 4、故障繼電器輸出信號，無源繼電器常開點輸出。<\/span><\/span> <\/p> 5、軟啟動、軟停機功能，防止設備啟動或停機過程中，對電網和設備的沖擊。<\/span><\/span> <\/p> 6、數字<\/span>PID<\/span>恒壓或相關參量恒定閉環控制模式。<\/span><\/span> <\/p> 7、常規啟動<\/span>/<\/span>停機與故障緊急停機、故障封鎖功能，有效保護設備的運行安全。<\/span><\/span> <\/p> 8、可控硅移相角調節范圍：<\/span>180<\/span>。<\/span><\/sup>，調節精度：<\/span>0.1%<\/span>。<\/span><\/span> <\/p> 9、單路可控硅觸發容量：<\/span><=1000A<\/span>。<\/span><\/span> <\/p> 10、具有開環、閉環二種運行模式，可自由切換。<\/span><\/span> <\/p> <\/span> <\/p> 指示燈說明：<\/strong><\/span><\/span> <\/p> RUN指示燈：系統待機狀態時，閃亮；系統運行時，常亮。<\/span><\/span> <\/p> FAT指示燈：系統運行過程中，過流保護延時時，閃亮；過流保護停機或外部緊急保護停機時，常亮。<\/span><\/span> <\/p> PID指示燈：系統<\/span>PID<\/span>閉環運行時，常亮；系統開環運行時，不亮。<\/span><\/span> <\/p> <\/span> <\/p> 接線端子說明：<\/strong><\/span><\/span> <\/p> LX\\NX ：<\/span> AC220V<\/span>供電接線端，兼容<\/span>AC220V<\/span>電源同步信號輸入功能。電網電壓適應范圍：<\/span>AC160V<\/span>～<\/span>260V<\/span>，功耗：<\/span>< 5W<\/span>。<\/span><\/span> <\/p> PE ：接地保護端。<\/span><\/span> <\/p> DK/COM ：繼電器無源常開點輸出端，觸點容量：<\/span>2A<\/span>/260V<\/span>。<\/span><\/span> <\/p> H0/H1 ：<\/span>AC0<\/span>～<\/span>5A<\/span>交流電流互感器接線端，用于交流電流反饋。<\/span><\/span> <\/p> K1/G1 ：可控硅觸發信號輸出端，可控硅觸發容量：<\/span><=3000A<\/span>。<\/span><\/span> <\/p> K2/G2 ：可控硅觸發信號輸出端，可控硅觸發容量：<\/span><=3000A<\/span>。<\/span><\/span> <\/p> PV ：<\/span>DC149V<\/span>直流高壓電壓信號輸入端口。此端口為非隔離輸入，應用時，請采用安全有效的控制方案，確保人身與設備安全！！<\/span><\/b> <\/p> FV ：<\/span>DC0<\/span>～<\/span>10V<\/span>反饋信號輸入端，用于壓力、流量、溫度等標準傳感器的反饋輸入，實現相關參量恒定運行功能。<\/span><\/span> <\/p> 注意：<\/span>PV/FV<\/span>二者，只能選用其一。<\/span><\/span> <\/p> FG ：<\/span>PV/FV<\/span>反饋信號公共端。<\/span><\/span> <\/p> REF ：調速信號參考電源端，用于外接調速電位器。電位器阻值范圍：<\/span>1.0K<\/span>～<\/span>10.0K<\/span>，建議使用<\/span>1.0K<\/span>電位器，以提高抗干擾能力。<\/span><\/span> <\/p> SG ：調速信號輸入公共端。<\/span><\/span> <\/p> SV ：<\/span>DC0<\/span>～<\/span>10V<\/span>電壓調速信號輸入端。<\/span><\/span> <\/p> SA ：<\/span>DC4<\/span>～<\/span>20mA<\/span>電流調速信號輸入端。<\/span><\/span> <\/p> DM ：數字信號輸入公共端。<\/span><\/span> <\/p> DI1 ：正常啟動<\/span>/<\/span>停機數字信號輸入端，與“<\/span>DM<\/span>”短接時，輸入有效。<\/span><\/span> <\/p> DI2 ：緊急保護停機數字信號輸入端，與“<\/span>DM<\/span>”短接時，輸入有效。<\/span><\/span> <\/p>
