■ Brushless precision
■ Resolver control
■ Transducer control
■ Memory intelligence
18EPE12Q
48EPE25D3
Electric Nutrunners – Corded Transducer Control
Pistol Grip Tools
Max Output Torque (Nm)
Under 60 Nm, rounded up to the nearest 1 Nm.
Over 60 Nm, rounded to the nearest 5 Nm.
Motor
18, 48
Tool Style
P – Pistol
Power
E-Electric
XX E P E XXX XX X
Output Drive
Q – Quick change D3 – 3/8” Sq.Dr.
D2 – 1/4” Sq.Dr. D4 – 1/2” Sq.Dr.
D6 – 3/4” Sq.Dr. D8 – 1” Sq.Dr.
Retainer
- Pin retainer
B Ball retainer
Connector
Air-LB
37
Push-to-Start Series
Torque Range Bolt Size
2 - 12 Nm M5 - M6
1.5 - 8.9 Ft. Lbs. #10 - 1/4”
■ Brushless precision
■ Resolver control
■ Transducer control
■ Memory intelligence
Push-to-Start Torque Range Max.
Speed Weight* Output
Drive
Size
Length Side to Center
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm
18EPE06QP 1.5-4.4 2-6 4000 2.66 1.19 1/4” Hex 9.35 238 0.84 21
18EPE06D3P 1.5-4.4 2-6 4000 2.66 1.19 3/8” 8.8 224 0.84 21
18EPE12QP 2.2-8.9 3-12 1820 2.83 1.27 1/4” Hex 9.35 196 0.84 21
18EPE12D3P 2.2-8.9 3-12 1820 2.83 1.27 3/8” 8.8 224 0.84 21
18ESE06QP 1.5-4.4 2-6 4000 2.93 1.31 1/4” Hex 14.75 375 0.91 23
18ESE06D3P 1.5-4.4 2-6 4000 2.93 1.31 3/8” 14.20 360 0.91 23
18ESE12QP 2.2-8.9 3-12 1820 3.10 1.40 1/4” Hex 14.75 375 0.91 23
18ESE12D3P 2.2-8.9 3-12 1820 3.10 1.40 3/8” 14.20 360 0.91 23
*Weights are without tool cable or suspension bail.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector; Suspension Bail (pistol only); Dead Handle (301857)
is included with 18CPE12Q & 18CPE12D3.
Tools with Matrix connector available upon request.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
18EPE06QP
18ESE06QP
Electric Nutrunners – Corded Transducer Control
Push-to-Start Pistol Grip/Inline Tools
Max Output Torque (Nm)
Under 60 Nm, rounded up to the nearest 1 Nm.
Motor
18, 48
Tool Style
P – Pistol
S – Inline
Power
E-Electric
XX E P E XX XX P
Output Drive
Q – Quick change
D3 – 3/8” Sq.Dr.
Connector Push-to-Start
Air-LB
38
Inline Floating Spindle
Series
Torque Range Bolt Size
2 - 248 Nm M5 - M16
1.5 - 182.9 Ft. Lbs. #10 - 5/8”
■ Brushless precision
■ Resolver control
■ Transducer control
■ Memory intelligence
Inline
Floating Spindle Torque Range Max.
Speed Weight* Output
Drive
Size
Length Side to Center
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm
18ESE06ZA 1.5-4.4 2-6 4000 3.0 1.4 1/4 15.5 394 0.91 23
18ESE12ZA 2.2-8.9 3-12 1820 3.2 1.5 1/4 16.0 406 0.91 23
18ESE17ZA 3.0-12.5 4-17 1290 3.2 1.5 1/4 16.0 406 0.91 23
48ESE12ZA 2.2-8.9 3-12 4000 3.4 1.5 1/4 16.7 425 0.91 23
48ESE271ZB 5.9-19.9 8-27 1820 5.8 2.6 3/8 22.0 559 0.92 23
48ESE361ZB 5.2-26.6 7-36 1290 5.8 2.6 3/8 22.0 559 0.92 23
48ESE602ZB 8.1-42.0 11-57 855 8.4 3.8 1/2 24.4 620 1.10 28
48ESE702ZB 10.3-50.2 14-68 570 8.4 3.8 1/2 24.4 620 1.10 28
48ESE802ZB 12.5-60.5 17-82 450 9.6 4.4 1/2 26.7 678 1.10 31
48ESE1152ZB 18.4-84.8 25-115 320 9.6 4.4 1/2 26.7 678 1.10 31
48ESE1502ZB 22.9-110.6 31-150 245 9.6 4.4 1/2 26.7 678 1.10 31
48ESE1653ZB 24.3-121.7 33-165 220 14.6 6.6 3/4 28.6 726 1.57 40
48ESE2503ZB 36.8-182.9 50-248 145 14.6 6.6 3/4 28.6 726 1.57 40
*Weights are without tool cable or reaction bar if so equipped.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector. Tool square drives have thru hole output.
Tools with Matrix connector available upon request.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
48ESE12ZA
1 22”
58 87mm
2 318”
1 159”
29 43mm
669”
16 99mm
1 339”
34 01mm
3 15”
80 01mm
31 1mm
ZA 1ZB 2ZB 3ZB
Dimensional Spindle Float: 1” (25mm) ZA
2” (50mm) 1ZB, 2ZB, 3ZB
tolerances = ± 004” (0 1mm)
0 25”
6 3mm
1 22”
31 1mm 1 31”
33 3mm
1 73”
44 0mm
0 35”
9 0mm
1 37”
34 9mm
1 41”
35 92mm
1 41”
35 92mm
2 00”
50 8mm
1 97”
50 04mm
1 559”
39 6mm
1 50”
38 1mm
1 10”
27 94mm
M5 x 0 8
Thd Typ
Base Plate Mounting Dimensions
Electric Nutrunners – Corded Transducer Control
Inline Floating Spindle Tools
Output Drive
ZA – 1/4” Sq.Dr.
1ZB – 3/8” Sq.Dr.
2ZB – 1/2” Sq.Dr.
3ZB – 3/4” Sq.Dr.
Max Output Torque (Nm)
Under 60 Nm, rounded up to the nearest 1 Nm.
Over 60 Nm, rounded to the nearest 5 Nm.
Motor
18, 48
Tool Style
S – Inline
Power
E-Electric
XX E S E XXX XXX
Connector
Air-LB
39
67ES2060Z8
Inline
Floating Spindle Torque Range Max.
Speed Weight* Output
Drive
Size
Length Side to Center
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm
67ES65BZ4 10-47 13-64 535 10.8 4.9 1/2 21.0 533 1.31 33
67ES105BZ4 15-77 21-104 330 10.8 4.9 1/2 21.0 533 1.31 33
67ES135BZ4 20-100 27-135 245 10.8 4.9 1/2 21.0 533 1.31 33
67ES190Z6 28-140 38-190 165 15.6 7.1 3/4 22.0 559 1.31 33
67ES285Z6 42-210 57-285 115 15.6 7.1 3/4 22.0 559 1.31 33
67ES385Z6 57-285 77-386 83 15.6 7.1 3/4 22.0 559 1.31 33
67ES475Z6 70-350 95-475 67 16.0 7.3 3/4 22.4 569 1.31 33
67ES610Z6 90-450 122-610 50 16.0 7.3 3/4 22.4 569 1.31 33
67ES850Z8 125-625 170-848 33 20.0 9.1 1 23.8 605 1.50 38
67ES1050Z8 155-775 210-1050 27 20.0 9.1 1 23.8 605 1.50 38
67ES1670Z8 246-1230 334-1668 17 20.0 9.1 1 23.8 605 1.50 38
67ES2060Z8 304-1520 412-2060 14 20.0 9.1 1 23.8 605 1.50 38
*Weights are without tool cable or reaction bar if so equipped.
Note: All 67 series tools require an isolation transformer (544185PT) for use with Cleco
Global Controller.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Matrix Connector; 67ES series – Mounting plate.
Extra Equipment: Std. tool cable 542778-XX, RA swivel cable 544055-XX,
Inline swivel cable 544056-XX, Extension cable 542779-XX.
Additional Accessories: See pages 121-129 for additional accessories.
Inline Floating Spindle
Series
Torque Range Bolt Size
13 - 2060 Nm M6 - M36
10 - 1520 Ft. Lbs. 1/4” - 1 1/2”
■ Brushless precision
■ Resolver control
■ Transducer control
■ Memory intelligence
67ES Base Plate Mounting Dimensions
Spindle Float: .69” (17mm)
2.372”
2.375”
PILOT DIA.
1.185”
.281” DIA.
THRU
2 HOLES
1.685”
1.563”
Z4
2.005”
3.010”
1.505”
3/8-24
UNF
TH'D DIA.
3.750”
2.500”
2.499”
PILOT DIA.
Z6
Spindle Float: .75” (19mm)
4.000”
4.020”
7/16-20
UNF-2B
TH’D DIA.
5.000”
4.000”
2.000”
2.010”
3.000”
3.010”
2.991”
2.990”
PILOT DIA.
Z8
Spindle Float:
1.0” (25mm)
Electric Nutrunners – Corded Transducer Control
Inline Floating Spindle Tools
Motor
67
Tool Style
S – Inline
Electric
67 E S XXXX XX
Output Drive
Z4 – 1/2” Sq.Dr.
Z6 – 3/4” Sq.Dr.
Z8 – 1” Sq.Dr.
Max Output Torque (Nm)
Under 60 Nm, rounded up to the nearest 1 Nm.
Over 60 Nm, rounded to the nearest 5 Nm.
Isolation
Transformer
544185PT
Incoming
Power
115/230VAC
Matrix Tool
Cable
542778-XM
Cleco 67 Series Tool
Air-Lb Cable
Power
Cable
All 67 Series Tools require an isolation
transformer (544185PT) for use with Cleco
Global Controller.
40
Hold & Drive tool approaches
the application.
Hold socket fits over bolt and
prevents it from rotating.
Tool is pushed down and started until drive
socket engages and tightens nut.
Hold & Drive Torque Range Free
Speed Length Weight* Head Height Side to Center
Model Number Ft.Lbs. Nm RPM in. mm lbs. kg in. mm in. mm
48EAE53H 8.1 – 39.1 11 – 53 850 20.2 512 7.9 3.60 2.40 61 1.06 27
48EAE75H 11.1 – 54.6 15 – 74 600 20.2 512 7.9 4.03 2.40 61 1.06 27
48EAE110H 17.0 – 82.6 23 – 112 400 20.2 512 8.9 4.03 2.40 61 1.06 27
48EAE135H 20.7 – 98.8 28 – 134 270 20.6 522 8.9 4.03 2.40 61 1.06 27
48EAE230H 34.7 – 167.4 47 – 227 150 22.2 563 10.6 4.79 2.40 61 1.06 27
*Weights are without tool cable and reaction bar.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector. Retraction 1” standard for hold bit.
Tools with Matrix connector available upon request.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
Hold & Drive Series
Torque Range
11 - 227 Nm
8.1 - 167.4 Ft. Lbs.
■ Brushless precision
■ Resolver control
■ Transducer control
■ Memory intelligence 48EAE115H
Electric Nutrunners – Corded Transducer Control
Hold & Drive Tools
48 E A E XXX H H X XX X XX X
Hold & Drive Tool Nomenclature Socket Nomenclature
Max Output Torque
Retainer Shaft
3 - 3 1/2”
4 - 4”
5 - 5 3/8”
6 - 5 7/8”
9 - 9 1/2”
Head Type
H-Hold & Drive
Connector
Air-LB
Motor
48
Tool
Style
A – Angle
Electric
Drive Socket Sizes (surface drive)
EH – 11/16 MG – 13mm MM – 19mm (3/4”) MS – 25mm
EJ – 13/16 MH – 14mm MN – 20mm MT – 26mm
EK – 7/8 MI – 15mm MO – 21mm MU – 27mm (1 1/16”)
EM – 1 MJ – 16mm (5/8”) MP – 22mm MX – 30mm (1 3/16”)
EO – 1 1/8 MK – 17mm MQ – 23mm MZ – 32mm (1 1/4”)
ML – 18mm MR – 24mm (15/16”)
Hold
& Drive
Oval Dim. (length)
If socket style =0
(female oval)
Socket Style
F – Female Hex
M – Male Hex
T – Torx
O – Female Oval Hold Socket (width across flats)
EA – 1/4 ME – 11mm (7/16”)
EC – 3/8 MF – 12mm
M5 – 5mm 15 – T15
M6 – 6mm 20 – T20
MA – 7mm 25 – T25
MB – 8mm (5/16”) 30 – T30
MC – 9mm 40 – T40
MD – 10mm 45 – T45
50 – T50
Male Oval
(length)
Hold Size (width)
Output Drive Size
“Hold & Drive” bolts are
used with these tools in automotive
and truck frame applications. They
reduce assembly handling to one
person working from one side of the
workpiece. The bolt is held stationary
by the tool while the nut is tightened
from the same side.
Note: To order a tool include the Socket Nomenclature with the Tool Nomenclature.
Order just the Socket Nomenclature for a complete head assembly.
Refer to Parts List for individual socket part numbers.
41
Flush Socket Series
Torque Range Bolt Size
4.9 - 230 Nm M8 - M21
3.6 - 169.6 Ft. Lbs. 1/2” - 1 3/16”
■ Brushless precision
■ Resolver control
■ Transducer control
■ Memory intelligence
18EAE30F1
Flush socket tools have plenty of clearance to fit low clearance
applications. Electric flush socket tools tighten with much higher
accuracy than tools with crowfoot attachment.
Overall Head Height
Available clearance
Electric Nutrunners – Corded Transducer Control
Flush Socket Tools
Flush
Socket Head
Type
Torque Range Free
Speed Weight* Length
Anglehead
Side to Center Height
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm in. mm
18EAE16F1 F1 3.6-11.8 4.9-16 1225 4.4 2.00 16.0 406 0.55 14 1.54 39
18EAE23F1 F1 3.4-17.0 4.6-23 860 4.4 2.00 16.0 406 0.55 14 1.54 39
18EAE30F1 F1 4.4-22.1 6.0-30 655 4.4 2.00 16.0 406 0.55 14 1.54 39
48EAE37F2 F2 5.9-27.3 8.0-37 1225 5.4 2.43 18.7 474 0.67 17 1.69 43
48EAE52F2 F2 8.1-38.3 11-52 860 5.4 2.43 18.7 474 0.67 17 1.69 43
48EAE53F3 F3 8.1-39.0 11-53 850 6.0 2.74 20.0 509 0.87 22 2.32 59
48EAE75F3 F3 11.1-55.3 15-75 600 6.0 2.74 20.0 509 0.87 22 2.32 59
48EAE110F3 F3 17.0-81.1 23-110 400 7.4 3.38 20.5 521 0.87 22 2.32 59
48EAE135F4 F4 19.9-99.5 27-135 270 8.9 4.03 20.6 522 1.06 27 2.40 61
48EAE230F4 F4 34.7-169.6 47-230 150 10.6 4.79 22.2 563 1.06 27 2.40 61
*Weights are without tool cable or reaction bar if so equipped.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector.
Tools with Matrix connector available upon request.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
X Dimension For Flush Socket
Head in. mm Socket Size Range
F1 1.54 39 8–15mm
F2 1.69 43 10–15mm
F3 2.32 59 13–21mm
F4 2.4 61 17–21mm
FX XX X X
Head Type
F1 Head 8–15mm socket capacity
F2 Head 10–15mm socket capacity
F3 Head 13–21mm socket capacity
F4 Head 13–21mm socket capacity
Motor
18
48 Tool Style
A – Right Angle
Electric Connector
Air-LB
Output Type
0–Standard 1–Fast Lead 2–Magnetic
Extension Length
0 – Flush 4 – 1/2” 8 – 1”
2 – 1/4” 6 – 3/4”
Flush Socket Tool Nomenclature Socket Nomenclature
XX E A E XXX FX
Socket Size
EC – 3/8 MB – 8mm (5/16) MJ – 16mm (5/8”)
EE – 1/2 MD – 10mm MK – 17mm
EF – 9/16 ME – 11mm (7/16) ML – 18mm
EH – 11/16 MF – 12mm MM – 19mm (3/4”)
EJ – 13/16 MG – 13mm MN – 20mm
MH – 14mm MO – 21mm
MI – 15mm
Max Output Torque
F1 16,23, 30 Nm F3 53, 75, 110 Nm
F2 37, 52 Nm F4 135, 230 Nm
<60 Nm, rounded up to the nearest 1 Nm. >60 Nm,
rounded to the nearest 5 Nm.
Flush
Socket
1 F1
2 F2
3 F3
4 F4
Note: To order a tool include the Socket Nomenclature with the Tool Nomenclature.
Order just the Socket Nomenclature for a complete head assembly.
Refer to Parts List for individual socket part numbers.
42
T2
T3
T4
“B”
T2, T3 & T4
Head Height
“A”
2.63” (67 mm) 1.56” (40 mm)
T2 Head T3 Head
1.44” (37 mm)
“A” “C”
“D”
T4 Head
1.94” (49 mm)
“A”
“C”
“D”
“C”
“D”
Tube Nut Max.
Drive
Size
Torque Range Free
Speed Weight* Length
Head
A Width B Blade Ht. C Opening D End/Cntr.
Model Number Ft.Lbs. Nm RPM lbs. kg in. mm in. mm in. mm in. mm in. mm
48ETE20T2 1/2” 7.4-14.8 10-20 1425 4.4 2.0 16.9 430 1.42 36 0.55 14 0.28 7 0.53 13
48ETE30T3 3/4” 11.1-22.1 15-30 1030 4.5 2.0 16.6 422 1.65 42 0.59 15 0.475 13 0.73 19
48ETE40T4 1 1/16” 14.8-29.5 20-40 770 5.3 2.3 17.9 454 2.36 60 0.59 15 0.675 18 0.93 24
*Weights are without tool cable and reaction bar.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector.
Tools with Matrix connector available upon request.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
Tube Nut Series
Torque Range Bolt Size
10 - 40 Nm M6 - M10
7.4 - 29.5 Ft. Lbs. 1/4” - 3/8”
■ Brushless precision
■ Resolver control
■ Transducer control
■ Memory intelligence
The 48ET tube nut wrench alternates the
direction of rotation each time the lever is
actuated. When rotating in reverse, the socket
will stop at the open position.
Note: To order a tool include the Socket Nomenclature with the Tool Nomenclature.
Order T2XXXX for a complete head assembly (i.e. T2MF02)
To order individual sockets, use a “KS” prefix (i.e. KS2EA01 for a T2 1/4”, Flush, Thru Hex socket.)
Electric Nutrunners – Corded Transducer Control
Tube Nut Tools
Tube Nut Tool Nomenclature Socket Nomenclature
Max Output Torque
<60 Nm, rounded up to the nearest 1 Nm.
Head Type
T2 - 20 Nm
T3 - 30 Nm
T4 - 40 Nm
Motor
48
Connector
Air-LB
Tool Style
T – Tube Nut
Electric Output Type
0 -Partial Thru Hex 2 -Double Thru Hex
1 -Thru Hex 3 -Partial Thru
Double Hex
Extension Length
0 – Flush 4 – 1/2” 8 – 1”
2 – 1/4” 6 – 3/4”
Maximum Hex Socket Size
MG, EE T2 Head Type
MM, 3/4” T3 Head Type
MU, 1 1/16” T4 Head Type
00, ## (Specials) All Head Types
Thru Hex Double
Thru Hex
Partial
Thru Hex
Partial Thru
Double Hex
Head Type
KS2 – T2
KS3 – T3
KS4 – T4
XX E T E XX XX KSX XX XX X
Socket Sizes
EA - 1/4” M5 – 5mm MH – 14mm MP – 22mm
EC – 3/8 M6 – 6mm MI – 15mm MQ – 23mm
EE – 1/2 MA – 7mm MJ – 16mm (5/8) MR – 24mm (15/16)
EF – 9/16 MB – 8mm (5/16) MK – 17mm MS – 25mm
EH – 11/16 MD – 10mm ML – 18mm MT – 26mm
EJ – 13/16 ME – 11mm (7/16) MM – 19mm (3/4) MU – 27mm (1 1/16)
EK – 7/8 MF – 12mm MN – 20mm
EM – 1 MG – 13mm MO – 21mm
43
48ECE30C 1
Crowfoot Torque Range Free
Speed Weight* Length
Model Number
15° Head 30° Head ft. lbs. Nm RPM lbs. kg in. mm
48ECE30C1 48ECE30C3 5.2-22.1 10.5-30 860 5.5 2.3 20.5 521
*Weights are without tool cable and reaction bar.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector.
Tools with Matrix connector available upon request.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
Crowfoot Series
Torque Range Bolt Size
7 - 30 Nm M6 - M8
5 - 22 Ft. Lbs. #10 - 3/8”
■ Brushless precision
■ Resolver control
■ Transducer control
■ Memory intelligence
Note: To order a tool include the Socket Nomenclature with the Tool Nomenclature.
To order individual sockets, use “CS” prefix before the required socket. (i.e. CSEA01 for a 1/4”, flush, thru hex socket.)
Electric Nutrunners – Corded Transducer Control
Crowfoot Tools
.61”
(15.49)
.97”
(24.63)
.75”
(19)
3.00”
(76.2)
30°
R.63”
(16)
1.25”
(31.75)
1.50”
(38.1)
.25”
(6.35)
C3 – 30° Head (Part No. 301960)
Maximum Recommended Torque: 22 ft.lbs. (30 Nm)
15°
.61”
(15.49)
1.09”
(27.86)
.75”
(19)
3.00”
(76.2)
2.66”
(67.56)
1.50”
(38.1)
1.25”
(31.75)
R.63”
(16)
.25”
(6.35)
C1 – 15° Head (Part No. 301959)
Maximum Recommended Torque: 22 ft.lbs. (30 Nm)
Max Output Torque
Head Type
C1 - 15° Crowfoot
C3 - 30° Crowfoot
Motor
48
Tool Style
C – Crowfoot
Electric
Socket Size
EA – 1/4” MC – 9mm
EC – 3/8 MD – 10mm
EE – 1/2 ME – 11mm (7/16)
EF – 9/16 MF – 12mm
MA – 7mm MG – 13mm
MB – 8mm (5/16) MH – 14mm
MI – 15mm*
*Fragile. Light duty apps.
Crowfoot Tool Nomenclature Socket Nomenclature
Output Style
1 – Thru Hex
Socket Type
CS – Crowfoot
Extension Length
0 – Flush
4 – 1/2”
6 – 3/4”
48 E C E XX XX CS XX XX X
Connector
Air-LB
44
Right Angle
Floating Spindle Series
Torque Range Bolt Size
5.1 - 255 Nm M7 - M18
3.7 - 188.1 Ft. Lbs. 1/4” - 3/4”
■ Brushless precision
■ Resolver control
■ Transducer control
■ Memory intelligence
Right Angle
Floating Spindle Torque Range Max.
Speed Weight* Output
Drive
Size
Length Side to Center
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm
18EAE16S131 3.7-11.8 5.1-16 1225 4.4 2.00 3/8” 16.0 406 0.55 14
18EAE23S131 5.3-16.9 7.2-23 860 4.4 2.00 3/8” 16.0 406 0.55 14
18EAE30S131 4.4-22.1 6.0-30 655 4.4 2.00 3/8” 16.0 406 0.55 14
48EAE37S231 5.9-27.2 8.0-37 1225 5.4 2.43 3/8” 18.7 474 0.67 17
48EAE52S231 8.1-38.3 11-52 860 5.4 2.43 3/8” 18.7 474 0.67 17
48EAE53S341 8.1-39.1 11-53 850 6.0 2.74 1/2” 20.0 509 0.87 22
48EAE75S341 11.0-55.3 15-75 600 6.0 2.74 1/2” 20.0 509 0.87 22
48EAE95S341 14.7-70.0 20-95 460 7.4 3.38 1/2” 20.5 521 0.87 22
48EAE110S341 16.9-81.1 23-110 400 7.4 3.38 1/2” 20.5 521 0.87 22
48EAE135S461 20.6-99.5 28-135 270 8.9 4.03 3/4” 20.6 522 1.06 27
48EAE230S461 34.6-169.6 47-230 150 10.6 4.79 3/4” 22.2 563 1.06 27
67EA150S461 22.1-110.6 30-150 210 12.9 5.90 3/4” 25.8 655 1.03 26
67EA185S461 27.3-136.3 37-185 170 12.9 5.90 3/4” 25.8 655 1.03 26
67EA210S461 31.0-154.8 42-210 155 12.9 5.90 3/4” 25.8 655 1.03 26
67EA235S461 33.9-169.6 46-230 135 12.9 5.90 3/4” 25.8 655 1.03 26
67EA255S461 40.6-188.1 55-255 115 12.9 5.90 3/4” 25.8 655 1.03 26
*Weights are without tool cable and mounting plate.
Note: All 67 series tools require an isolation transformer (544185PT) for use with Cleco
Global Controller.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: 18/48 tools; Air-LB Connector; Mounting plate.
Tools with Matrix connector available upon request.
67 tools; Matrix Connector; Mounting plate
Extra Equipment: 18/48 tools; Std. tool cable 301866-XX, RA swivel cable
301903-XX, Inline swivel cable 301904-XX, Extension cable 301877-XX.
67 tools; Std. tool cable 542778-XX, RA swivel cable 544055-XX,
Inline swivel cable 544056-XX, Extension cable 542779-XX.
Additional Accessories: See pages 121-129 for additional accessories.
48EAE135S461
Max Output Torque
S1 Head – 16, 23, or 30 Nm
S2 Head – 37 or 52 Nm
S3 Head – 53, 75, 95, or 110 Nm
S4 Head – 135 or 230 Nm (48 series)
S4 Head – 150, 185, 210, 235 or
255 Nm (67 series)
Tool Termination
S1 Sliding (Floating) Spindle S3 Sliding (Floating) Spindle
S2 Sliding (Floating) Spindle S4 Sliding (Floating) Spindle
Motor
18
48
67
Connector
E - Air-LB
Tool Style
A – Right Angle
Electric
XX E A X XXX XX X X
Extension Length
1 –1.13” (S1), 1.00” (S2 & S3), 1.25” (S4)
2 –2.13” (S1), 3.00” (S2), 2.5” (S4 1/2” Dr.)
5 –5.13” (S2), 4.25” (S4)
6 – 6.0” (S4 1/2” Dr.), 7.0” (S4 3/4” Dr.)
11 – 11.0” (S4 3/4” Dr.)
Square Drive
3 – 3/8” (S1, S2)
4 – 1/2” (S3, S4)
6 – 3/4” (S4)
Right Angle Floating Spindle Tool Nomenclature
Electric Nutrunners – Corded Transducer Control
Right Angle Floating Spindle Tools
Isolation
Transformer
544185PT
Incoming
Power
115/230VAC
Matrix Tool
Cable
542778-XM
Cleco 67 Series Tool
Air-Lb Cable
Power
Cable
All 67 Series Tools require an
isolation transformer (544185PT)
for use with Cleco Global Controller.
45
S3 Head
Extension Length “X”
1 –1.0” (1/2” Sq. Dr.)
S4 Head
Extension Length “X”
1 –1.25” (1/2” & 3/4” Sq. Dr.)
2 –2.5” (1/2” Sq. Dr.)
5 –4.25” (1/2” & 3/4” Sq. Dr.)
6 –6.0” (1/2” Sq. Dr.)
6 –7.0” (3/4” Sq. Dr.)
11 –11.0” (3/4” Sq. Dr.)
18EA, 48EA & 67EA Floating Spindle Angle Heads
S1 Head
Extension Length “X”
1 –1.13” (3/8” Sq. Dr.)
2 –2.13” (3/8” Sq. Dr.)
S2 Head
Extension Length “X”
1 –1.0” (3/8” Sq. Dr.)
2 –3.0” (3/8” Sq. Dr.)
5 –5.13” (3/8” Sq. Dr.)
Electric Nutrunners – Corded Transducer Control
Right Angle Floating Spindle Tools
46
Controller (Page 115)
Corded Tool,
Transducer Control (Pages 32-44)
Corded Tool,
Current Control (Pages 48-58)
Cable (Page 121-122)
Input Accessories (Page 124)
Output Accessories (Page 124) Input Accessory Cables (Page 124)
Output Accessory Cables (Page 124)
Input to Input Accessory Cables (Page 124) Isolation Transformer (Page 121) (Refer to Pages 26-27 to build a mPro400GC-M/GC-P/GC-S system.)
How To Build A DC Fastening System
mPro400GC-E & mPro400GC-I
Building a DC System for Quality Critical applications
is as simple as 1, 2, 3!
1. Choose a common system to the right.
2. Select the correct components below.
3. Order your System!
47
mPro400GC-E (Transducer Control) 1 1 1 1 1
mPro400GC-I (Current Control) 1 1
18/48E_EXXX 1 1 1 1
67E_XXX 1
18/48C_EXXX 1 1
Tool Cable - 301866-XM (Air-Lb) 1 1 1 1 1 1
Tool Cable - 542778-XM (Matrix) 1
Extension Cable - 301877-XM (If Required) (Air-Lb)
Extension Cable - 542779-XM (If Required) (Matrix)
542977-X Torque Selector Switch 1 1
542978-X Socket Tray
544241PT - 4-pos Bit & Socket Tray (cable included)
544242PT - 8-pos Bit & Socket Tray (cable included) 1
54297X - Start/Stop Switches 1
542976-1 Annunciator 1
544237-1M Input Accessory Cable
544237-5M Input Accessory Cable
544237-10M Input Accessory Cable
544237-15M Input Accessory Cable
1 1
544238-1M Output Accessory Cable
544238-5M Output Accessory Cable
544238-10M Output Accessory Cable
544238-15M Output Accessory Cable
1
542986-X - Input to Input Accessory Cable 1
544185PT 1
One Corded Tool (18/48E_E)
One Corded Tool (67E_XXX)
One Corded Tool (18/48E_E) & Torque Selector
One Corded Tool (18/48E_E) & Annunciator
One Corded CC Tool (18/48C_EXXX)
One Corded CC Tool (18/48C_E) & 8 Pos. Socket Tray
One Corded Tool (18/48E_E) & 2 Accessories
Model/Part Number
Add or delete components
as required.
48
18CAE28AM3
48CAE58AM3
Right
Angle Series
Torque Range
2 - 230 Nm
1.5 - 170 Ft. Lbs.
Bolt Size
M5 - M16
#10 - 5/8”
■ Brushless precision
■ Resolver control
■ Memory intelligence
Right Angle Torque Range Max.
Speed Weight* Output
Drive
Size
Length
Anglehead
Side to Center Height
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm in. mm
18CAE08AL2 1.5-5.9 2-8 3000 2.9 1.3 1/4” 13.6 345 0.51 13 1.4 36
18CAE15AM3 3.0-11.1 4-15 1300 3.3 1.5 3/8” 14.8 376 0.59 15 1.6 41
18CAE22AM3 3.7-16.2 5-22 920 3.3 1.5 3/8” 14.8 376 0.59 15 1.6 41
18CAE28AM3 4.4-20.7 6-28 700 3.3 1.5 3/8” 14.8 376 0.59 15 1.6 41
48CAE15AL3 2.2-11.1 3-15 2855 3.8 1.7 3/8” 15.7 398 0.59 15 1.6 41
48CAE28AL3 4.4-20.7 6-28 1300 4.1 1.9 3/8” 16.2 410 0.59 15 1.6 41
48CAE41AM3 6.6-30.2 9-41 1090 4.3 2.0 3/8” 17.3 440 0.75 19 1.9 48
48CAE58AM3 8.9-42.8 12-58 770 4.3 2.0 3/8” 17.3 440 0.75 19 1.9 48
48CAE58AM4 8.9-42.8 12-58 770 4.3 2.0 1/2” 17.3 440 0.75 19 1.9 48
48CAE90AH4 13.3-64.2 18-87 515 6.6 3.0 1/2” 18.5 470 0.81 21 2.3 58
48CAE105AH4 15.5-76.7 21-104 340 6.6 3.0 1/2” 18.5 470 0.81 21 2.3 58
48CAE135MH4 19.9-98.1 27-133 265 7.3 3.3 1/2” 19.1 485 0.94 24 2.4 61
48CAE175AX6 26.6-129.8 36-176 190 10.2 4.6 3/4” 21.6 549 1.06 27 2.7 69
48CAE230AX6 33.9-169.6 46-230 145 10.2 4.6 3/4” 21.6 549 1.06 27 2.7 69
*Weights are without tool cable and reaction bar.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector. Ball retainer optional.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
Electric Nutrunners – Corded Current Control
Right Angle Tools
Tool Style
A – Right Angle
Current
Control
XX C A E XXX XXX X
Retainer
- Pin retainer
B Ball retainer
Output Drive
AL2 – 1/4” Sq.Dr. AM4 – 1/2” Sq.Dr.
AL3 – 3/8” Sq.Dr. AH4 – 1/2” Sq.Dr.
AM3 – 3/8” Sq.Dr. MH4 – 1/2” Sq.Dr.
AX6 – 3/4” Sq.Dr.
Connector
E-Air-LB
Motor
18, 48
Max Output Torque (Nm)
Under 60 Nm, rounded up to the nearest 1 Nm.
Over 60 Nm, rounded to the nearest 5 Nm.
49
18CSE06Q
48CSE25D3
Inline
Non-Floating
Series
Torque Range
2 - 150 Nm
1.5 - 113 Ft. Lbs.
Bolt Size
M5 - M14
#10 - 5/8”
■ Brushless precision
■ Resolver control
■ Memory intelligence
Inline Non-Floating Torque Range Max.
Speed Weight* Output
Drive
Size
Length Side to Center
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm
18CSE06Q 1.5-4.4 2-6 4000 2.5 1.1 1/4” Hex 12.3 312 0.91 23
18CSE06D2 1.5-4.4 2-6 4000 2.5 1.1 1/4” 11.8 300 0.91 23
18CSE12Q 2.2-8.9 3-12 1820 2.7 1.2 1/4” Hex 13.0 330 0.91 23
18CSE12D3 2.2-8.9 3-12 1820 2.7 1.2 3/8” 12.4 315 0.91 23
18CSE17Q 3.0-12.5 4-17 1290 2.7 1.2 1/4” Hex 13.0 330 0.91 23
18CSE17D3 3.0-12.5 4-17 1290 2.7 1.2 3/8” 12.4 315 0.91 23
18CSE22D3 3.7-16.2 5-22 985 2.7 1.2 3/8” 12.4 315 0.91 23
18CSE31D3 5.2-22.9 7-31 695 2.7 1.2 3/8” 12.4 315 0.91 23
48CSE12Q 2.2-8.9 3-12 4000 3.0 1.4 1/4” Hex 13.5 343 0.91 23
48CSE12D2 2.2-8.9 3-12 4000 3.0 1.4 1/4” 13.0 330 0.91 23
48CSE25D3 4.4-18.4 6-25 1820 3.2 1.5 3/8” 13.6 345 0.91 23
48CSE36D3 5.9-26.6 8-36 1290 3.2 1.5 3/8” 13.6 345 0.91 23
48CSE48D3 7.4-35.4 10-48 985 3.3 1.5 3/8” 13.8 351 0.91 23
48CSE65D4 9.6-47.9 13-65 750 5.3 2.4 1/2” 16.6 420 1.13 29
48CSE90D4 14.0-66.4 19-90 510 5.6 2.5 1/2” 17.1 435 1.13 29
48CSE125D4 19.2-92.2 26-125 360 5.6 2.5 1/2” 17.1 435 1.13 29
48CSE150D4 22.9-110.6 31-150 240 5.6 2.5 1/2” 17.1 435 1.13 29
*Weights are without tool cable and reaction bar.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector; Dead Handle is included with 18CSE12Q and
18CSE12D3. Reaction bar is included with inline tools with output torques of 17-150 NM.
Ball retainer optional.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Mounting Plates: 543231 - (all with exception of listed below)
543235 - 18ES06Q/D2, 48ES12Q/D2
49087108 - 48ES65D4, 48ES90D4, 48ES125D4, & 48ES150D4.
Additional Accessories: See pages 121-129 for additional accessories.
Electric Nutrunners – Corded Current Control
Inline Non-Floating Spindle Tools
Motor
18, 48
Tool Style
S – Inline
Current
Control
XX C S E XXX XX X
Retainer
- Pin retainer
B Ball retainer
Output Drive
Q – Quick change D3 – 3/8” Sq.Dr.
D2 – 1/4” Sq.Dr. D4 – 1/2” Sq.Dr.
Connector
E – Air-LB
Max Output Torque (Nm)
Under 60 Nm, rounded up to the nearest 1 Nm.
Over 60 Nm, rounded to the nearest 5 Nm.
50
Pistol Grip
Series
Torque Range
2 - 150 Nm
1.5 - 110 Ft. Lbs.
Bolt Size
M5 - M14
#10 - 5/8”
■ Brushless precision
■ Resolver control
■ Memory intelligence
Pistol Grip Torque Range Max.
Speed Weight* Output
Drive
Size
Length Side to Center
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm
18CPE06Q 1.5-4.4 2-6 4000 2.2 1.0 1/4” Hex 7.0 178 0.84 21
18CPE06D2 1.5-4.4 2-6 4000 2.2 1.0 1/4” 6.5 165 0.84 21
18CPE12Q 2.2-8.9 3-12 1820 2.4 1.1 1/4” Hex 7.7 196 0.84 21
18CPE12D3 2.2-8.9 3-12 1820 2.4 1.1 3/8” 7.2 183 0.84 21
18CPE17Q 3.0-12.5 4-17 1290 2.4 1.1 1/4” Hex 7.7 196 0.84 21
18CPE17D3 3.0-12.5 4-17 1290 2.4 1.1 3/8” 7.2 183 0.84 21
18CPE22D3 3.7-16.2 5-22 985 2.4 1.1 3/8” 7.2 183 0.84 21
18CPE31D3 5.2-22.9 7-31 695 2.4 1.1 3/8” 7.2 183 0.84 21
48CPE12Q 2.2-8.9 3-12 4000 2.7 1.2 1/4” Hex 8.3 211 0.84 21
48CPE12D2 2.2-8.9 3-12 4000 2.7 1.2 1/4” 7.7 196 0.84 21
48CPE25D3 4.4-18.4 6-25 1820 2.9 1.3 3/8” 8.4 213 0.84 21
48CPE36D3 5.9-26.6 8-36 1290 2.9 1.3 3/8” 8.4 213 0.84 21
48CPE48D3 7.4-35.4 10-48 985 3.0 1.4 3/8” 8.6 218 0.84 21
48CPE65D4 9.6-47.9 13-65 750 5.0 2.3 1/2” 10.8 274 1.1 28
48CPE90D4 14.0-66.4 19-90 510 5.3 2.4 1/2” 11.3 287 1.1 28
48CPE125D4 19.2-92.2 26-125 360 5.3 2.4 1/2” 11.3 287 1.1 28
48CPE150D4 22.9-110.6 31-150 240 5.3 2.4 1/2” 11.3 287 0.9 23
*Weights are without tool cable and reaction bar.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector; Suspension Bail; Dead Handle is included with
18CPE12Q & 18CPE12D3. Reaction bar is included with pistol tools with output torques of
17-150 Nm. Ball retainer optional.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
18CPE6Q
48CPE25D3
Electric Nutrunners – Corded Current Control
Pistol Grip Tools
Tool Style
P – Pistol
Current
Control
XX C P E XXX XX X
Retainer
- Pin retainer
B Ball retainer
Output Drive
Q – Quick change D3 – 3/8” Sq.Dr.
D2 – 1/4” Sq.Dr. D4 – 1/2” Sq.Dr.
Connector
E-Air-LB
Motor
18, 48
Max Output Torque (Nm)
Under 60 Nm, rounded up to the nearest 1 Nm.
Over 60 Nm, rounded to the nearest 5 Nm.
51
Push-to-Start
Series
Torque Range
2 - 12 Nm
1.5 - 8.9 Ft. Lbs.
Bolt Size
M5 - M6
#10 - 1/4”
■ Brushless precision
■ Resolver control
■ Memory intelligence
Push-to-Start Torque Range Max.
Speed Weight* Output
Drive
Size
Length Side to Center
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm
18CPE06QP 1.5-4.4 2-6 4000 2.66 1.19 1/4” Hex 9.35 238 0.84 21
18CPE06D3P 1.5-4.4 2-6 4000 2.66 1.19 3/8” 8.8 224 0.84 21
18CPE12QP 2.2-8.9 3-12 1820 2.83 1.27 1/4” Hex 9.35 196 0.84 21
18CPE12D3P 2.2-8.9 3-12 1820 2.83 1.27 3/8” 8.8 224 0.84 21
18CSE06QP 1.5-4.4 2-6 4000 2.93 1.31 1/4” Hex 14.75 375 0.91 23
18CSE06D3P 1.5-4.4 2-6 4000 2.93 1.31 3/8” 14.20 360 0.91 23
18CSE12QP 2.2-8.9 3-12 1820 3.10 1.40 1/4” Hex 14.75 375 0.91 23
18CSE12D3P 2.2-8.9 3-12 1820 3.10 1.40 3/8” 14.20 360 0.91 23
*Weights are without tool cable and reaction bar.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector; Suspension Bail on pistol models; Dead Handle
(301857) is included with 18CPE12Q & 18CPE12D3.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
18CPE06QP
18CSE06QP
Electric Nutrunners – Corded Current Control
Push-to-Start Pistol Grip/Inline Tools
Tool Style
P – Pistol
S – Inline
Current
Control
XX C X E XXX XX P
Push-to-Start
Output Drive
Q – Quick change
D3 – 3/8” Sq.Dr.
Connector
E-Air-LB
Motor
18, 48
Max Output Torque (Nm)
Under 60 Nm, rounded up to the nearest 1 Nm.
52
Inline Floating
Spindle Series
Torque Range
2 - 248 Nm
1.5 - 182.9 Ft. Lbs.
Bolt Size
M5 - M16
#10 - 5/8”
■ Brushless precision
■ Resolver control
■ Memory intelligence
Inline
Floating Spindle Torque Range Max.
Speed Weight* Output
Drive
Size
Length Side to Center
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm
18CSE06ZA 1.5-4.4 2-6 4000 3.0 1.4 1/4 15.5 394 0.91 23
18CSE12ZA 2.2-8.9 3-12 1820 3.2 1.5 1/4 16.0 406 0.91 23
18CSE17ZA 3.0-12.5 4-17 1290 3.2 1.5 1/4 16.0 406 0.91 23
48CSE12ZA 2.2-8.9 3-12 4000 3.4 1.5 1/4 16.7 425 0.91 23
48CSE271ZB 5.9-19.9 8-27 1820 5.8 2.6 3/8 22.0 559 0.92 23
48CSE361ZB 5.2-26.6 7-36 1290 5.8 2.6 3/8 22.0 559 0.92 23
48CSE602ZB 8.1-42.0 11-57 855 8.4 3.8 1/2 24.4 620 1.10 28
48CSE702ZB 10.3-50.2 14-68 570 8.4 3.8 1/2 24.4 620 1.10 28
48CSE802ZB 12.5-60.5 17-82 450 9.6 4.4 1/2 26.7 678 1.10 31
48CSE1152ZB 18.4-84.8 25-115 320 9.6 4.4 1/2 26.7 678 1.10 31
48CSE1502ZB 22.9-110.6 31-150 245 9.6 4.4 1/2 26.7 678 1.10 31
48CSE1653ZB 24.3-121.7 33-165 220 14.6 6.6 3/4 28.6 726 1.57 40
48CSE2503ZB 36.8-182.9 50-248 145 14.6 6.6 3/4 28.6 726 1.57 40
*Weights are without tool cable or reaction bar if so equipped.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector.
Tool square drives have thru hole output.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
1 22”
58 87mm
2 318”
1 159”
29 43mm
669”
16 99mm
1 339”
34 01mm
3 15”
80 01mm
31 1mm
ZA 1ZB 2ZB 3ZB
Dimensional Spindle Float: 1” (25mm) ZA
2” (50mm) 1ZB, 2ZB, 3ZB
tolerances = ± 004” (0 1mm)
0 25”
6 3mm
1 22”
31 1mm 1 31”
33 3mm
1 73”
44 0mm
0 35”
9 0mm
1 37”
34 9mm
1 41”
35 92mm
1 41”
35 92mm
2 00”
50 8mm
1 97”
50 04mm
1 559”
39 6mm
1 50”
38 1mm
1 10”
27 94mm
M5 x 0 8
Thd Typ
Base Plate Mounting Dimensions
18CSE12ZA
Electric Nutrunners – Corded Current Control
Inline Floating Spindle Tools
Tool Style
S – Inline
Current
Control
XX C S E XXX XXX
Output Drive
ZA – 1/4” Sq.Dr.
1ZB – 3/8” Sq.Dr.
2ZB – 1/2” Sq.Dr.
3ZB – 3/4” Sq.Dr.
Connector
E-Air-LB
Motor
18, 48
Max Output Torque (Nm)
Under 60 Nm, rounded up to the nearest 1 Nm.
Over 60 Nm, rounded to the nearest 5 Nm.
53
48CAE110H
Hold & Drive Torque Range Free
Speed Length Weight* Head Height Side to Center
Model Number Ft.Lbs. Nm RPM in. mm lbs. kg in. mm in. mm
48CAE53H 8.1 – 39.8 11 – 54 850 20.2 512 7.9 3.60 2.40 61 1.06 27
48CAE75H 11.1 – 56.8 15 – 77 600 20.2 512 7.9 4.03 2.40 61 1.06 27
48CAE110H 17.0 – 85.6 23 – 115 400 20.2 512 8.9 4.03 2.40 61 1.06 27
48CAE135H 20.7 – 101.8 28 – 135 270 20.6 522 8.9 4.03 2.40 61 1.06 27
48CAE230H 34.7 – 169.6 47 – 230 150 22.2 563 10.6 4.79 2.40 61 1.06 27
*Weights are without tool cable or reaction bar if so equipped.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector. Retraction 1” standard for hold bit.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
Hold & Drive Series
Torque Range
11 - 227 Nm
8.1 - 167.4 Ft. Lbs.
■ Brushless precision
■ Resolver control
■ Memory intelligence
Electric Nutrunners – Corded Current Control
Hold & Drive Tools
H X XX X XX X
Hold & Drive Tool Nomenclature Head Assembly Nomenclature
48 C A E XXX H
Max Output Torque
Retainer Shaft
3 - 3 1/2”
4 - 4”
5 - 5 3/8”
6 - 5 7/8”
9 - 9 1/2”
Motor
48
Current
Control
Socket Style
F – Female Hex
M – Male Hex
T – Torx
O – Female Oval
Oval Dim. (length)
If socket style =0
(female oval)
Connector
E – Air-LB
Tool Style
A – Right Angle
Hold
& Drive
Head Type
H-Hold & Drive
Drive Socket Sizes (surface drive)
EH – 11/16 MH – 14mm MN – 20mm MS – 25mm
EJ – 13/16 MI – 15mm MO – 21mm MT – 26mm
EK – 7/8 MJ – 16mm (5/8”) MP – 22mm MU – 27mm (1 1/16”)
EM – 1 MK – 17mm MQ – 23mm MX – 30mm (1 3/16”)
EO – 1 1/8 ML – 18mm MR – 24mm (15/16”) MZ – 32mm (1 1/4”)
MG – 13mm MM – 19mm (3/4”)
Hold Socket (width across flats)
EA - 1/4 15 – T15
EC – 3/8 20 – T20
M5 – 5mm 25 – T25
M6 – 6mm 30 – T30
MA – 7mm 40 – T40
MB – 8mm (5/16”) 50 – T50
MC – 9mm
MD – 10mm
ME – 11mm (7/16”)
MF – 12mm
Male Oval
(length)
Hold Size (width)
Output Drive Size
Hold & Drive tool approaches
the application.
Hold socket fits over bolt and
prevents it from rotating.
Tool is pushed down and started until drive
socket engages and tightens nut.
“Hold & Drive” bolts are used
with these tools in automotive
and truck frame applications.
They reduce
assembly handling
to one person
working from one
side of the workpiece. The bolt
is held stationary by the tool
while the nut is tightened from
the same side.
Note: To order a tool include the Socket Nomenclature with the Tool Nomenclature.
Order just the Socket Nomenclature for a complete head assembly.
Refer to Parts List for individual socket part numbers.
54
Flush Socket Series
Torque Range Bolt Size
4.9 - 234 Nm M8 - M21
3.6 - 172.6 Ft. Lbs. 1/2” - 1 3/16”
■ Brushless precision
■ Resolver control
■ Memory intelligence
Flush Socket Head
Type
Torque Range Free
Speed Weight* Length
Anglehead
Side to Center Height
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm in. mm
18CAE16F1 F1 3.6-11.8 4.9-16 1225 4.4 2.00 16.0 406 0.55 14 1.54 39
18CAE23F1 F1 3.4-17.0 4.6-23 860 4.4 2.00 16.0 406 0.55 14 1.54 39
18CAE30F1 F1 4.4-22.1 6.0-30 655 4.4 2.00 16.0 406 0.55 14 1.54 39
48CAE37F2 F2 5.9-27.3 8.0-37 1225 5.4 2.43 18.7 474 0.67 17 1.69 43
48CAE52F2 F2 8.1-38.3 11-52 860 5.4 2.43 18.7 474 0.67 17 1.69 43
48CAE53F3 F3 8.1-39.0 11-53 850 6.0 2.74 20.0 509 0.87 22 2.32 59
48CAE75F3 F3 11.1-55.3 15-75 600 6.0 2.74 20.0 509 0.87 22 2.32 59
48CAE110F3 F3 17.0-81.1 23-110 400 7.4 3.38 20.5 521 0.87 22 2.32 59
48CAE135F4 F4 19.9-99.5 27-135 270 8.9 4.03 20.6 522 1.06 27 2.40 61
48CAE230F4 F4 34.7-172.6 47-230 150 10.6 4.79 22.2 563 1.06 27 2.40 61
*Weights are without tool cable or reaction bar if so equipped.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
18CAE30F1
Electric Nutrunners – Corded Current Control
Flush Socket Tools
FX XX X X
Max Output Torque
F1 16,23, 30 Nm F3 53, 75, 110 Nm
F2 37, 52 Nm F4 135, 230 Nm
<60 Nm, rounded up to the nearest 1 Nm. >60 Nm,
rounded to the nearest 5 Nm.
Head Type
F1 Head 8–15mm socket capacity
F2 Head 10–15mm socket capacity
F3 Head 13–21mm socket capacity
F4 Head 13–21mm socket capacity
Motor
18, 48
Tool Style
A – Right Angle
Current
Control
Flush
Socket
1 F1
2 F2
3 F3
4 F4
Output Type
0–Standard 1–Fast Lead 2–Magnetic
Extension Length
0 – Flush 4 – 1/2” 8 – 1”
2 – 1/4” 6 – 3/4”
Flush Socket Tool Nomenclature Socket Nomenclature
XX C A E XXX FX
Connector
E – Air-LB
Socket Size
EC – 3/8 MB – 8mm (5/16”) MJ – 16mm (5/8”)
ED – 7/16 MD – 10mm MK – 17mm
EE – 1/2 ME – 11mm (7/16”) ML – 18mm
EF – 9/16 MF – 12mm MM – 19mm (3/4”)
EH – 11/16 MG – 13mm MN – 20mm
EJ – 13/16 MH – 14mm MO – 21mm
MI – 15mm
X Dimension For Flush Socket
Head in. mm Socket Size Range
F1 1.54 39 8–15mm
F2 1.69 43 10–15mm
F3 2.32 59 13–21mm
F4 2.4 61 17–21mm
Flush socket tools have plenty of clearance to fit low clearance
applications. Electric flush socket tools tighten with much higher
accuracy than tools with crowfoot attachment.
Overall Head Height
Available clearance
Note: To order a tool include the Socket Nomenclature with the Tool Nomenclature.
Order just the Socket Nomenclature for a complete head assembly.
Refer to Parts List for individual socket part numbers.
55
T2
T3
T4
“B”
T2, T3 & T4
Head Height
“A”
2.63” (67 mm) 1.56” (40 mm)
T2 Head T3 Head
1.44” (37 mm)
“A” “C”
“D”
T4 Head
1.94” (49 mm)
“A”
“C”
“D”
“C”
“D”
Tube Nut Max.
Drive
Size
Torque Range Free
Speed Weight* Length
Head
A Width B Blade Ht. C Opening D End/Cntr.
Model Number Ft.Lbs. Nm RPM lbs. kg in. mm in. mm in. mm in. mm in. mm
48CTE20T2 1/2” 7.4-14.8 10-20 1425 4.4 2.0 16.9 430 1.42 36 0.55 14 0.28 7 0.53 13
48CTE30T3 3/4” 11.1-22.1 15-30 1030 4.5 2.0 16.6 422 1.65 42 0.59 15 0.475 13 0.73 19
48CTE40T4 1 1/16” 14.8-29.5 20-40 770 5.3 2.3 17.9 454 2.36 60 0.59 15 0.675 18 0.93 24
*Weights are without tool cable and reaction bar.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
Tube Nut Series
Torque Range Bolt Size
10 - 40 Nm M6 - M10
7.4 - 29.5 Ft. Lbs. 1/4” - 3/8”
■ Brushless precision
■ Resolver control
The 48ET tube nut wrench alternates the ■ Memory intelligence
direction of rotation each time the lever is
actuated. When rotating in reverse, the socket
will stop at the open position.
Electric Nutrunners – Corded Current Control
Tube Nut Tools
Tube Nut Tool Nomenclature Socket Nomenclature
Max Output Torque
<60 Nm, rounded up to the nearest 1 Nm.
Head Type
T2 - 20 Nm
T3 - 30 Nm
T4 - 40 Nm
Motor
48
Tool Style
T – Tube Nut
Current
Control
Output Type
0 -Partial Thru Hex 2 -Double Thru Hex
1 -Thru Hex 3 -Partial Thru
Double Hex
Extension Length
0 – Flush 4 – 1/2” 8 – 1”
2 – 1/4” 6 – 3/4”
Maximum Hex Socket Size
MG, EE T2 Head Type
MM, 3/4” T3 Head Type
MU, 1 1/16” T4 Head Type
00, ## (Specials) All Head Types
Thru Hex Double
Thru Hex
Partial
Thru Hex
Partial Thru
Double Hex
Connector
E – Air-LB
Head Type
KS2 – T2
KS3 – T3
KS4 – T4
XX C T E XX XX KSX XX XX X
Socket Sizes
EA - 1/4” M5 – 5mm MH – 14mm MP – 22mm
EC – 3/8 M6 – 6mm MI – 15mm MQ – 23mm
EE – 1/2 MA – 7mm MJ – 16mm (5/8) MR – 24mm (15/16)
EF – 9/16 MB – 8mm (5/16) MK – 17mm MS – 25mm
EH – 11/16 MD – 10mm ML – 18mm MT – 26mm
EJ – 13/16 ME – 11mm (7/16) MM – 19mm (3/4) MU – 27mm (1 1/16)
EK – 7/8 MF – 12mm MN – 20mm
EM – 1 MG – 13mm MO – 21mm
Note: To order a tool include the Socket Nomenclature with the Tool Nomenclature.
Order T2XXXX for a complete head assembly (i.e. T2MF02)
To order individual sockets, use a “KS” prefix (i.e. KS2EA01 for a T2 1/4”, Flush, Thru Hex socket.)
56
Right Angle
Floating Spindle Series
Torque Range Bolt Size
5.1 - 230 Nm M7 - M18
3.7 - 169.6 Ft. Lbs. 1/4” - 3/4”
■ Brushless precision
■ Resolver control
■ Memory intelligence
Right Angle
Floating Spindle Torque Range Max.
Speed Weight* Output
Drive
Size
Length Side to Center
Model Number ft. lbs. Nm RPM lbs. kg in. mm in. mm
18CAE16S131 3.7-11.8 5.1-16 1225 4.4 2.00 3/8” 16.0 406 0.55 14
18CAE23S131 5.3-16.9 7.2-23 860 4.4 2.00 3/8” 16.0 406 0.55 14
18CAE30S131 4.4-22.1 6.0-30 655 4.4 2.00 3/8” 16.0 406 0.55 14
48CAE37S231 5.9-27.2 8.0-37 1225 5.4 2.43 3/8” 18.7 474 0.67 17
48CAE52S231 8.1-38.3 11-52 860 5.4 2.43 3/8” 18.7 474 0.67 17
48CAE53S341 8.1-39.1 11-53 850 6.0 2.74 1/2” 20.0 509 0.87 22
48CAE75S341 11.0-55.3 15-75 600 6.0 2.74 1/2” 20.0 509 0.87 22
48CAE95S341 14.7-70.0 20-95 460 7.4 3.38 1/2” 20.5 521 0.87 22
48CAE110S341 16.9-81.1 23-110 400 7.4 3.38 1/2” 20.5 521 0.87 22
48CAE135S461 20.6-99.5 28-135 270 8.9 4.03 3/4” 20.6 522 1.06 27
48CAE230S461 34.6-169.6 47-230 150 10.6 4.79 3/4” 22.2 563 1.06 27
*Weights are without tool cable and mounting plate.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector; Mounting plate.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
48CAE135S461
Max Output Torque
S1 Head – 16, 23, or 30 Nm
S2 Head – 37 or 52 Nm
S3 Head – 53, 75, 95, or 110 Nm
S4 Head – 135 or 230 Nm (48 series)
Tool Termination
S1 Sliding (Floating) Spindle S3 Sliding (Floating) Spindle
S2 Sliding (Floating) Spindle S4 Sliding (Floating) Spindle
Motor
18
48
Tool Style
A – Right Angle
Current
Control
XX C A E XXX XX X X
Right Angle Floating Spindle Tool Nomenclature
Connector
E – Air-LB
Square Drive
3 - 3/8” (S1,S2)
4 - 1/2” (S3,S4)
6 - 3/4” (S4)
Extension Length
1 -1.13” (S1), 1.00” (S2 & S3), 1.25” (S4)
2 -2.13” (S1), 3.00” (S2), 2.5” (S4 1/2” Dr.)
5 -5.13” (S2), 4.25” (S4)
6 -6.0” (S4 1/2” Dr.), 7.0” (S4 3/4” Dr.)
11 -11.0” (S4 3/4” Dr.)
Electric Nutrunners – Corded Current Control
Right Angle Floating Spindle Tools
57
S3 Head
Extension Length “X”
1 –1.0” (1/2” Sq. Dr.)
S4 Head
Extension Length “X”
1 –1.25” (1/2” & 3/4” Sq. Dr.)
2 –2.5” (1/2” Sq. Dr.)
5 –4.25” (1/2” & 3/4” Sq. Dr.)
6 –6.0” (1/2” Sq. Dr.)
6 –7.0” (3/4” Sq. Dr.)
11 –11.0” (3/4” Sq. Dr.)
18CAE & 48CAE Floating Spindle Angle Heads
S1 Head
Extension Length “X”
1 –1.13” (3/8” Sq. Dr.)
2 –2.13” (3/8” Sq. Dr.)
S2 Head
Extension Length “X”
1 –1.0” (3/8” Sq. Dr.)
2 –3.0” (3/8” Sq. Dr.)
5 –5.13” (3/8” Sq. Dr.)
Electric Nutrunners – Corded Current Control
Right Angle Floating Spindle Tools
58
Max Output Torque
Head Type
C1 - 15° Crowfoot
C3 - 30° Crowfoot
Motor
48
Tool Style
C – Crowfoot
Current
Control
Socket Size
EA – 1/4” MC – 9mm
EC – 3/8 MD – 10mm
EE – 1/2 ME – 11mm (7/16)
EF – 9/16 MF – 12mm
MA – 7mm MG – 13mm
MB – 8mm (5/16) MH – 14mm
MI – 15mm*
*Fragile. Light duty apps.
Crowfoot Tool Nomenclature Socket Nomenclature
Output Style
1 – Thru Hex
Connector
E – Air-LB
Socket Type
CS – Crowfoot
Extension Length
0 – Flush
4 – 1/2”
6 – 3/4”
48 C C E XX XX CS XX XX X
Crowfoot Torque Range Free
Speed Weight* Length
Model Number
15° Head 30° Head ft. lbs. Nm RPM lbs. kg in. mm
48CCE30C1 48CCE30C3 7.7-22.1 10.5-30 860 5.5 2.3 20.5 521
*Weights are without tool cable and reaction bar.
General: All tools must be used with an approved ATG cable and controller.
Standard Equipment: Air-LB Connector.
Extra Equipment: Std. tool cable 301866-XX, RA swivel cable 301903-XX,
Inline swivel cable 301904-XX, Extension cable 301877-XX.
Additional Accessories: See pages 121-129 for additional accessories.
To order individual sockets, use a “CS” prefix before the required socket. (i.e. CSEA01 for a, 1/4”, flush, thru hex socket.)
Crowfoot Series
Torque Range Bolt Size
7 - 30 Nm M6 - M8
5 - 22 Ft. Lbs. #10 - 3/8”
■ Brushless precision
■ Resolver control
■ Memory intelligence
48CCE30C1
Electric Nutrunners – Corded Current Control
Crowfoot Tools
Note: To order a tool include the Socket Nomenclature with the Tool Nomenclature.
To order individual sockets, use “CS” prefix before the required socket. (i.e. CSEA01 for a 1/4”, flush, thru hex socket.)
59
.61”
(15.49)
.97”
(24.63)
.75”
(19)
3.00”
(76.2)
30°
R.63”
(16)
1.25”
(31.75)
1.50”
(38.1)
.25”
(6.35)
C3 – 30° Head (Part No. 301960)
Maximum Recommended Torque: 22 ft.lbs. (30 Nm)
15°
.61”
(15.49)
1.09”
(27.86)
.75”
(19)
3.00”
(76.2)
2.66”
(67.56)
1.50”
(38.1)
1.25”
(31.75)
R.63”
(16)
.25”
(6.35)
C1 – 15° Head (Part No. 301959)
Maximum Recommended Torque: 22 ft.lbs. (30 Nm)
60
How To Build A Fixtured DC Tool System
Building a Fixtured DC Tool System is as simple as 1, 2, 3!
1. Choose a common system to the right.
2. Select the correct components below.
3. Order your System!
System Control Package - Intelligent Spindle (Page 89)
Controller, Power Transformer, Power Distribution Box,
Arcnet Cable, and Stand
Intelligent Fixtured Spindle (Page 64-87) Floating Spindle Adapters (Page 122) Field Cables - Intelligent Spindle (Page 88) Jumper/Extension Cables - Intelligent Spindle (Page 88) System Bus Terminator at spindle - Intelligent Spindle (Page 88) Controller - Conventional Spindle (Page 114-118)
Conventional Fixtured Spindle (Pages 90-111) Floating Spindle Adapters (Page 113) Field Cables - Conventional Spindle (Page 122) Extension Cables - Conventional Spindle (Page 122) System Bus Cable - (Page 124)
61
Add or delete components
as required.
mPro400GCM PDBCPSXX - Select model from catalog. 1 1
Select from catalog. Floating spindle ordered separately. 1 2
Select from catalog. 1 2
Select cable with desired connector from catalog. 1 1
Select cable with desired connector from catalog. 1 1
961127 1 1
mPro400GC-SG-12 Compact Box 1 1
mPro400GC-SG-34 Compact Box 1 1
Select from catalog. Floating spindle ordered separately. 1 1 * *
Select from catalog. 1 1 * *
Select from catalog. 1 1 * *
Select from catalog. 1 1 * *
Select from catalog.
**(Included in the System Control Package) 1 1 ** **
*As required.
Conventional 1-2 Spindle (Size 1, 2)
Conventional 1-2 Spindle (Size 3, 4)
Conventional >2 Spindle (Size 1, 2)
Conventional >2 Spindle (Size 3, 4)
>2 Convent. Spindles - Consult Application Center
Single Intelligent Spindle
Two Intelligent Spindles
>2 Intelligent Spindles - Consult Application Center
Model/Part Number
62
Intelligent Spindles
With straight drive, offset drive, and angle drive
configurations, each available with reversible gears,
and four different motor sizes to suit different torque
requirements, there’s a DGD Intelligent Spindle to fit
most any situation. Your Apex Tool Group Technical
Sales Representative will work with you to determine
the best solution for you. We can also provide you
with application assistance in automation integration,
joint analysis testing, complex data connection, and
more.
There’s A DGD Intelligent Spindle Intelligent Spindle Sizes and Torque Ranges
Size 1
Size 2
Size 3
Size 4
Nm 0 100 200 300 400 ... 2.600 2.700 2.800
2-53 Nm
25-200 Nm
50-300 Nm
100-2800 Nm
Power
Supply
OUT
Servo amplifier and
measuring board
Service
access
panel
Connection cable
Motor for transducers
Torque
Transducer
Power
Supply
IN
Floating spindle adapter
(ordered separately)
Motor with servoamplifier
& measurement card
B - Brushless Motor
U - Reverse gearing
TS - Tightening System
E - Standard
Example
Size
1, 2, 3, 4
Gear
1 - Size
B - Brushless motor gear
XXX - Max. torque
A - Generation
2nd Transducer for cross check
2 - 2x only for Z attachment
Attachment
1 - Size
Z - Straight attachement
VK - Offset drive with transducer
WK - Angle drive with transducer
1 - Capacity level
B - Version
Transducer
1 - Size
K - Combination torque + angle
1 - Capacity level 1 or 2
B - Version
M - Only moment, no angle encoder
1 BTSE — 1B035A — 2/ 1M1B — 1ZB
X XXXX — XXXXXX — X XXXX — XXXXX
Note: Floating spindle adapter must be ordered separately.
Offset Drive
Offset Drive with
reversible gears
63
Spindle For Your Application
Intelligent Spindle Configurations
Straight Drive
Straight Drive with
reversible gears
Angle Drive
Angle Drive with
reversible gears
64
BTSE Models
Torque
Range
Speed
Float
Square
Drive
RPM Nm max. mm inch Straight drive, single transducer
2-12 1921 50 3/8" 5-35 727 50 3/8" 15-53 427 50 3/8" Straight drive with reversible gears, single transducer
2-12 1921 50 3/8" 5-35 727 50 3/8" 15-53 427 50 3/8" Offset drive, single transducer
2-12 1825 50 3/8" 5-35 690 50 3/8" 15-53 405 50 3/8" Offset drive with reversible gears, single transducer
2-12 1825 50 3/8" 5-35 690 50 3/8" 15-53 405 50 3/8" Angle drive, single transducer
2-12 1801 25 3/8" 5-35 681 25 3/8" 15-53 400 25 3/8" Angle drive with reversible gears, single transducer
2-12 1801 25 3/8" 5-35 681 25 3/8" 15-53 400 25 3/8" Smallest scribed circle diameter in mm
Number of spindles
Model 1
Attachment
Angle drive
Straight Offset
2 43 35 52
3 54 40 60
4 61 50 74
5 81 58 89
6 99 70 105
7 116 85 120
Intelligent Spindles 2 - 53 Nm
Size 1, Single Transducer
65
Min. Center-
Center
L Weight
Design
Order No.
DGD
Spindle
Floating Adapter
Floating Adapter
incl. guide housing
mm mm kg Order No. X (mm) Order No.
43 486 4.8 1BTSE-1B012A-1M3B-1ZB 922325PT 180 S308434
43 486 4.8 1BTSE-1B035A-1M1B-1ZB 922325PT 180 S308434
43 486 4.8 1BTSE-1B060A-1M2B-1ZB 922325PT 180 S308434
43 393 5.3 1BUTSE-1B012A-1M3B-1ZB 922325PT 180 S308434
43 393 5.3 1BUTSE-1B035A-1M1B-1ZB 922325PT 180 S308434
43 393 5.3 1BUTSE-1B060A-1M2B-1ZB 922325PT 180 S308434
35 474 5.3 1BTSE-1B012A-1VM3B 922325PT 180 S308437
35 474 5.3 1BTSE-1B035A-1VM1B 922325PT 180 S308437
35 474 5.3 1BTSE-1B060A-1VM2B 922325PT 180 S308437
35 382 5.8 1BUTSE-1B012A-1VM3B 922325PT 180 S308437
35 382 5.8 1BUTSE-1B035A-1VM1B 922325PT 180 S308437
35 382 5.8 1BUTSE-1B060A-1VM2B 922325PT 180 S308437
For angle attachement
52 542 5.7 1BTSE-1B012A-1WM3B 929041
52 542 5.7 1BTSE-1B035A-1WM1B 929041
52 542 5.7 1BTSE-1B060A-1WM2B 929041
For angle attachement
52 370 6.2 1BUTSE-1B012A-1WM3B 929041
52 370 6.2 1BUTSE-1B035A-1WM1B 929041
52 370 6.2 1BUTSE-1B060A-1WM2B 929041
The transducer can be rotated for crowded multiple spindle arrangements (DGD 15° radial toothing).
= maximum accessibility. Floating adapter not included with spindle.
2D and 3D are available to download at www.apexpowertools.com in the Customer Support section or on www.apexpowertools.eu
in the download area.
66
BTSE Models
Torque
Range
Speed
Float
Square
Drive
RPM Nm max. mm inch Straight drive, single transducer
25-110 890 50 1/2" 40-200 502 50 3/4" Straight drive with reversible gears, single transducer
25-110 890 50 1/2" 40-200 502 50 3/4" Offset drive, single transducer
25-110 831 50 1/2" 40-200 468 50 3/4" Offset drive with reversible gears, single transducer
25-110 831 50 1/2" 40-200 468 50 3/4" Angle drive, single transducer
25-110 838 25 1/2" 40-200 472 25 3/4" Angle drive with reversible gears, single transducer
25-110 838 25 1/2" 40-200 472 25 3/4" Smallest scribed circle diameter in mm
Number of spindles
Model 2
Attachment
Angle drive
Straight Offset
2 56 44 59
3 75 50 68
4 80 62 86
5 106 74 101
6 130 89 118
7 151 102 137
Intelligent Spindles 25 - 200 Nm
Size 2, Single Transducer
67
Min. Center-
Center
L Weight
Design
Order No.
DGD
Spindle
Floating Adapter
Floating Adapter
incl. guide housing
mm mm kg Order No. X (mm) Order No.
56 528 7.6 2BTSE-2B110A-2M1B-2ZB 910609 180 S308435
56 528 7.6 2BTSE-2B200A-2M3B-2ZB 935552 180 S308450
56 367 8.6 2BUTSE-2B110A-2M1B-2ZB 910609 180 S308435
56 367 8.6 2BUTSE-2B200A-2M3B-2ZB 935552 180 S308450
44 551 9.2 2BTSE-2B110A-2VM1B 910609 180 S308438
44 551 9.2 2BTSE-2B200A-2VM3B 935552 180 S308475
44 390 10.2 2BUTSE-2B110A-2VM1B 910609 180 S308438
44 390 10.2 2BUTSE-2B200A-2VM3B 935552 180 S308475
For angle attachement
59 581 8.7 2BTSE-2B110A-2WM1B 929053
59 581 8.7 2BTSE-2B200A-2WM3B 929061
For angle attachement
59 421 9.7 2BUTSE-2B110A-2WM1B 929053
59 421 9.7 2BUTSE-2B200A-2WM3B 929061
The transducer can be rotated for crowded multiple spindle arrangements (DGD 15° radial toothing).
= maximum accessibility. Floating adapter not included with spindle.
2D and 3D are available to download at www.apexpowertools.com in the Customer Support section or on www.apexpowertools.eu
in the download area.
68
BTSE Models
Torque
Range
Speed
Float
Square
Drive
RPM Nm max. mm inch Straight drive, single transducer
50-300 453 50 3/4" Straight drive with reversible gears, single transducer
50-300 453 50 3/4" versetzter Abtrieb, 1 Messwertaufnehmer / Offset drive, single transducer
50-300 421 50 3/4" Offset drive with reversible gears, single transducer
50-300 421 50 3/4" Angle drive, single transducer
50-300 437 25 3/4" Angle drive with reversible gears, single transducer
50-300 437 25 3/4" Smallest scribed circle diameter in mm
Number of spindles
Model 3
Attachment
Angle drive
Straight Offset
2 81 59 81
3 94 69 94
4 116 84 116
5 139 102 139
6 164 122 164
7 189 138 189
Intelligent Spindles 50 - 300 Nm
Size 3, Single Transducer
69
Min. Center-
Center
L Weight
Design
Order No.
DGD
Spindle
Floating Adapter
Floating Adapter
incl. guide housing
mm mm kg Order No. X (mm) Order No.
81 589 14.1 3BTSE-3B300A-3M2B-3ZB 910613 185 S308436
81 417 16.1 3BUTSE-3B300A-3M2B-3ZB 910613 185 S308436
59 584 15.2 3BTSE-3B300A-3VM2B 910613 185 S308439
59 412 17.2 3BUTSE-3B300A-3VM2B 910613 185 S308439
For angle attachement
81 678 17.8 3BTSE-3B300A-3WM2B 929065
For angle attachement
81 506 19.8 3BUTSE-3B300A-3WM2B 929065
The transducer can be rotated for crowded multiple spindle arrangements (DGD 15° radial toothing).
= maximum accessibility. Floating adapter not included with spindle.
2D and 3D are available to download at www.apexpowertools.com in the Customer Support section or on www.apexpowertools.eu
in the download area.
70
BTSE Models
Torque
Range
Speed
Float
Square
Drive
RPM Nm max. mm inch Straight drive, single transducer
100-500 254 50 3/4" 130-660 174 50 1" 320-12501 86 50 1" 400-16001 68 50 1 1/2" 980-2800 37 -- 1 1/2" Straight drive with reversible gears, single transducer
100-500 254 50 3/4" 130-660 174 50 1" 320-12501 86 50 1" 400-16001 68 50 1 1/2" Offset drive, single transducer
100-500 238 50 3/4" 130-660 163 50 1" 160-750 135 50 1" Offset drive with reversible gears, single transducer
100-500 238 50 3/4" 130-660 163 50 1" 160-750 135 50 1" Angle drive, single transducer
100-500 245 25 1" 130-660 167 25 1" Angle drive with reversible gears, single transducer
100-500 245 25 1" 130-660 167 25 1" 1 Special version - technical drawings on request.
Smallest scribed circle diameter in mm
Number of spindles
Model 4
Attachment
Angle drive
Straight * Offset
2 91 121 76 112
3 122 152 88 130
4 130 172 108 160
5 174 230 130 192
6 217 281 153 224
7 246 327 180 263
Intelligent Spindles 100 - 2800 Nm
Size 4, Single Transducer
71
Min. Center-
Center
L Weight
Design
Order No.
DGD
Spindle
Floating Adapter
Floating Adapter
incl. guide housing
mm mm kg Order No. X (mm) Order No.
91 719 21 4BTSE-4B500A-4M2B-4ZA 916643 190
91 719 21 4BTSE-4B660A-4M3B-4ZA 916642 186
121* 771 29 4BTSE-4B360A-4M1B-4Z1250A S976956 140
121* 771 29 4BTSE-4B500A-4M2B-4Z1600A S308441 140
160* 790 39.73 4BTSE-4B660A-4M3B-4Z2800G
91 546 22.5 4BUTSE-4B500A-4M2B-4ZA 916643 190
91 546 22.5 4BUTSE-4B660A-4M3B-4ZA 916642 186
121* 599 31 4BUTSE-4B360A-4M1B-4Z1250A S976956 140
121* 599 31 4BUTSE-4B500A-4M2B-4Z1600A S308441 140
76 684 22.5 4BTSE-4B500A-4VM2B 912106 190 S308440
76 684 22.5 4BTSE-4B660A-4VM3B 912147 186 S308474
76 684 23 4BTSE-4B660A-4VM4B 912147 186 S308474
76 512 24 4BUTSE-4B500A-4VM2B 912106 190 S308440
76 512 24 4BUTSE-4B660A-4VM3B 912147 186 S308474
76 512 24.5 4BUTSE-4B660A-4VM4B 912147 186 S308474
For angle attachement
112 729 27.1 4BTSE-4B500A-4WM2B 929089
112 729 27.1 4BTSE-4B660A-4WM3B 929089
For angle attachement
112 556 28.6 4BUTSE-4B500A-4WM2B 929089
112 556 28.7 4BUTSE-4B660A-4WM3B 929089
1 Special version - technical drawings on request
The transducer can be rotated for crowded multiple spindle arrangements (DGD 15° radial toothing).
= maximum accessibility. Floating adapter not included with spindle.
2D and 3D are available to download at www.apexpowertools.com in the Customer Support section or on www.apexpowertools.eu
in the download area.
72
BTS Models
Torque
Range
Speed
Float
Square
Drive
RPM Nm max. mm inch Straight drive, single transducer
2-12 1921 50 3/8" 5-35 727 50 3/8" 15-53 427 50 3/8" Straight drive with reversible gears, single transducer
2-12 1921 50 3/8" 5-35 727 50 3/8" 15-53 427 50 3/8" Offset drive, single transducer
2-12 1825 50 3/8" 5-35 690 50 3/8" 15-53 405 50 3/8" Offset drive with reversible gears, single transducer
2-12 1825 50 3/8" 5-35 690 50 3/8" 15-53 405 50 3/8" Angle drive, single transducer
2-12 1801 25 3/8" 5-35 681 25 3/8" 15-53 400 25 3/8" Angle drive with reversible gears, single transducer
2-12 1801 25 3/8" 5-35 681 25 3/8" 15-53 400 25 3/8" Smallest scribed circle diameter in mm
Number of spindles
Model 1
Attachment
Angle drive
Straight Offset
2 43 35 52
3 54 40 60
4 61 50 74
5 81 58 89
6 99 70 105
7 116 85 120
Intelligent Spindles 2 - 53 Nm
Size 1, Single Transducer
73
Min. Center-
Center
L Weight
Design
Order No.
DGD
Spindle
Floating Adapter
Floating Adapter
incl. guide housing
mm mm kg Order No. X (mm) Order No.
43 486 4.8 1BTS-1B012A-1K3B-1ZB 947541A8 922325PT 180 S308434
43 486 4.8 1BTS-1B035A-1K1B-1ZB 947553A4 922325PT 180 S308434
43 486 4.8 1BTS-1B060A-1K2B-1ZB 947565A0 922325PT 180 S308434
43 393 5.3 1BUTS-1B012A-1K3B-1ZB 947547A2 922325PT 180 S308434
43 393 5.3 1BUTS-1B035A-1K1B-1ZB 947559A8 922325PT 180 S308434
43 393 5.3 1BUTS-1B060A-1K2B-1ZB 947571A2 922325PT 180 S308434
35 474 5.3 1BTS-1B012A-1VK3B 947543A6 922325PT 180 S308437
35 474 5.3 1BTS-1B035A-1VK1B 947555A2 922325PT 180 S308437
35 474 5.3 1BTS-1B060A-1VK2B 947567A8 922325PT 180 S308437
35 382 5.8 1BUTS-1B012A-1VK3B 947549A0 922325PT 180 S308437
35 382 5.8 1BUTS-1B035A-1VK1B 947561A4 922325PT 180 S308437
35 382 5.8 1BUTS-1B060A-1VK2B 947573A0 922325PT 180 S308437
For angle attachement
52 542 5.7 1BTS-1B012A-1WK3B 947545A4 929041
52 542 5.7 1BTS-1B035A-1WK1B 947557A0 929041
52 542 5.7 1BTS-1B060A-1WK2B 947569A6 929041
For angle attachement
52 370 6.2 1BUTS-1B012A-1WK3B 947551A6 929041
52 370 6.2 1BUTS-1B035A-1WK1B 947563A2 929041
52 370 6.2 1BUTS-1B060A-1WK2B 947575A8 929041
The transducer can be rotated for crowded multiple spindle arrangements (DGD 15° radial toothing).
= maximum accessibility. Floating adapter not included with spindle.
2D and 3D are available to download at www.apexpowertools.com in the Customer Support section or on www.apexpowertools.eu
in the download area.
74
BTS Models
Torque
Range
Speed
Float
Square
Drive
RPM Nm max. mm inch Straight drive, twin transducer (redundant)
2-12 1921 50 3/8" 5-35 727 50 3/8" 15-53 427 50 3/8" Straight drive with reversible gears, twin transducer (redundant)
2-12 1921 50 3/8" 5-35 727 50 3/8" 15-53 427 50 3/8" Offset drive, twin transducer (redundant)
2-12 1825 50 3/8" 5-35 690 50 3/8" 15-53 405 50 3/8" Offset drive with reversible gears, twin transducer (redundant)
2-12 1825 50 3/8" 5-35 690 50 3/8" 15-53 405 50 3/8" Angle drive, twin transducer (redundant)
2-12 1801 25 3/8" 5-35 681 25 3/8" 15-53 400 25 3/8" Angle drive with reversible gears, twin transducer (redundant)
2-12 1801 25 3/8" 5-35 681 25 3/8" 15-53 400 25 3/8" Smallest scribed circle diameter in mm
Number of spindles
Model 1
Attachment
Angle drive
Straight Offset
2 43 35 52
3 54 40 60
4 61 50 74
5 81 58 89
6 99 70 105
7 116 85 120
Intelligent Spindles 2 - 53 Nm
Size 1, Twin Transducer (redundant)
75
Min. Center-
Center
L Weight
Design
Order No.
DGD
Spindle
Floating Adapter
Floating Adapter
incl. guide housing
mm mm kg Order No. X (mm) Order No.
43 566 5.4 1BTS-1B012A-2/1K3B-1ZB 947542A7 922325PT 180 S308434
43 566 5.4 1BTS-1B035A-2/1K1B-1ZB 947554A3 922325PT 180 S308434
43 566 5.4 1BTS-1B060A-2/1K2B-1ZB 947566A9 922325PT 180 S308434
43 393 5.9 1BUTS-1B012A-2/1K3B-1ZB 947548A1 922325PT 180 S308434
43 393 5.9 1BUTS-1B035A-2/1K1B-1ZB 947560A5 922325PT 180 S308434
43 393 5.9 1BUTS-1B060A-2/1K2B-1ZB 947572A1 922325PT 180 S308434
35 554 5.9 1BTS-1B012A-1K3B-1VK3B 947544A5 922325PT 180 S308437
35 554 5.9 1BTS-1B035A-1K1B-1VK1B 947556A1 922325PT 180 S308437
35 554 5.9 1BTS-1B060A-1K2B-1VK2B 947568A7 922325PT 180 S308437
35 382 6.4 1BUTS-1B012A-1K3B-1VK3B 947550A7 922325PT 180 S308437
35 382 6.4 1BUTS-1B035A-1K1B-1VK1B 947562A3 922325PT 180 S308437
35 382 6.4 1BUTS-1B060A-1K2B-1VK2B 947574A9 922325PT 180 S308437
For angle attachement
52 622 6.3 1BTS-1B012A-1K3B-1WK3B 947546A3 929041
52 622 6.3 1BTS-1B035A-1K1B-1WK1B 947558A9 929041
52 622 6.3 1BTS-1B060A-1K2B-1WK2B 947570A3 929041
For angle attachement
52 450 6.8 1BUTS-1B012A-1K3B-1WK3B 947552A5 929041
52 450 6.8 1BUTS-1B035A-1K1B-1WK1B 947564A1 929041
52 450 6.8 1BUTS-1B060A-1K2B-1WK2B 947576A7 929041
The transducer can be rotated for crowded multiple spindle arrangements (DGD 15° radial toothing).
= maximum accessibility. Floating adapter not included with spindle.
2D and 3D are available to download at www.apexpowertools.com in the Customer Support section or on www.apexpowertools.eu
in the download area.
76
BTS Models
Torque
Range
Speed
Float
Square
Drive
RPM Nm max. mm inch Straight drive, single transducer
25-110 890 50 1/2" 40-200 502 50 3/4" Straight drive with reversible gears, single transducer
25-110 890 50 1/2" 40-200 502 50 3/4" Offset drive, single transducer
25-110 831 50 1/2" 40-200 468 50 3/4" Offset drive with reversible gears, single transducer
25-110 831 50 1/2" 40-200 468 50 3/4" Angle drive, single transducer
25-110 838 25 1/2" 40-200 472 25 3/4" Angle drive with reversible gears, single transducer
25-110 838 25 1/2" 40-200 472 25 3/4" Smallest scribed circle diameter in mm
Number of spindles
Model 2
Attachment
Angle drive
Straight Offset
2 56 44 59
3 75 50 68
4 80 62 86
5 106 74 101
6 130 89 118
7 151 102 137
Intelligent Spindles 25 - 200 Nm
Size 2, Single Transducer
77
Min. Center-
Center
L Weight
Design
Order No.
DGD
Spindle
Floating Adapter
Floating Adapter
incl. guide housing
mm mm kg Order No. X (mm) Order No.
56 528 7.6 2BTS-2B110A-2K1B-2ZB 947517A8 910609 180 S308435
56 528 7.6 2BTS-2B200A-2K3B-2ZB 947529A4 935552 180 S308450
56 367 8.6 2BUTS-2B110A-2K1B-2ZB 947519A6 910609 180 S308435
56 367 8.6 2BUTS-2B200A-2K3B-2ZB 947531A0 935552 180 S308450
44 551 9.2 2BTS-2B110A-2VK1B 947521A2 910609 180 S308438
44 551 9.2 2BTS-2B200A-2VK3B 947533A8 935552 180 S308475
44 390 10.2 2BUTS-2B110A-2VK1B 947523A0 910609 180 S308438
44 390 10.2 2BUTS-2B200A-2VK3B 947535A6 935552 180 S308475
For angle attachement
59 581 8.7 2BTS-2B110A-2WK1B 947525A8 929053
59 581 8.7 2BTS-2B200A-2WK3B 947537A4 929061
For angle attachement
59 421 9.7 2BUTS-2B110A-2WK1B 947527A6 929053
59 421 9.7 2BUTS-2B200A-2WK3B 947539A2 929061
The transducer can be rotated for crowded multiple spindle arrangements (DGD 15° radial toothing).
= maximum accessibility. Floating adapter not included with spindle.
2D and 3D are available to download at www.apexpowertools.com in the Customer Support section or on www.apexpowertools.eu
in the download area.
78
BTS Models
Torque
Range
Speed
Float
Square
Drive
RPM Nm max. mm inch Straight drive, twin transducer (redundant)
25-110 890 50 1/2" 40-200 502 50 3/4" Straight drive with reversible gears, twin transducer (redundant)
25-110 890 50 1/2" 40-200 502 50 3/4" Offset drive, twin transducer (redundant)
25-110 831 50 1/2" 40-200 468 50 3/4" Offset drive with reversible gears, twin transducer (redundant)
25-110 831 50 1/2" 40-200 468 50 3/4" Angle drive, twin transducer (redundant)
25-110 838 25 1/2" 40-200 472 25 3/4" Angle drive with reversible gears, twin transducer (redundant)
25-110 838 25 1/2" 40-200 472 25 3/4" Smallest scribed circle diameter in mm
Number of spindles
Model 2
Attachment
Angle drive
Straight Offset
2 56 44 59
3 75 50 68
4 80 62 86
5 106 74 101
6 130 89 118
7 151 102 137
Intelligent Spindles 25 - 200 Nm
Size 2, Twin Transducer (redundant)
79
Min. Center-
Center
L Weight
Design
Order No.
DGD
Spindle
Floating Adapter
Floating Adapter
incl. guide housing
mm mm kg Order No. X (mm) Order No.
56 625 8.7 2BTS-2B110A-2/2K1B-2ZB 947518A7 910609 180 S308435
56 625 8.7 2BTS-2B200A-2/2K3B-2ZB 947530A1 935552 180 S308450
56 464 9.7 2BUTS-2B110A-2/2K1B-2ZB 947520A3 910609 180 S308435
56 464 9.7 2BUTS-2B200A-2/2K3B-2ZB 947532A9 935552 180 S308450
44 648 10.3 2BTS-2B110A-2K1B-2VK1B 947522A1 910609 180 S308438
44 648 10.3 2BTS-2B200A-2K3B-2VK3B 947534A7 935552 180 S308475
44 487 11.3 2BUTS-2B110A-2K1B-2VK1B 947524A9 910609 180 S308438
44 487 11.3 2BUTS-2B200A-2K3B-2VK3B 947536A5 935552 180 S308475
For angle attachement
59 678 9.8 2BTS-2B110A-2K1B-2WK1B 947526A7 929053
59 678 9.8 2BTS-2B200A-2K3B-2WK3B 947538A3 929061
For angle attachement
59 518 9.7 2BUTS-2B110A-2K1B-2WK1B 947528A5 929053
59 518 9.7 2BUTS-2B200A-2K3B-2WK3B 947540A9 929061
The transducer can be rotated for crowded multiple spindle arrangements (DGD 15° radial toothing).
= maximum accessibility. Floating adapter not included with spindle.
