橡膠止水帶和止水橡皮是以天然橡膠與各種合成橡膠為主要原料,摻加各種助劑及填充料,經塑煉、混煉、壓制成型，其品種規格較多，有橋型、山型、P型、U型、Z型、乙型、T型、H型、E型、Q型等。根據使用情況又可分類為埋式橡膠止水帶和背貼式橡膠止水帶。該止水材料具有良好的彈性,耐磨性、耐老化性和抗撕裂性能,適應變形能力強、防水性能好，溫度使用范圍為-45℃-+60℃.當溫度超過70℃,以及橡膠止水帶受強烈的氧化作用或受油類等有機溶劑侵蝕時，均不得使用橡膠止水帶.
The rubber sealing strip and sealing rubber with natural rubber and various synthetic rubber as the main raw material, and the filling material mixed with various additives, through plasticizing, mixing, molding, the more varieties of different specifications, bridge, mountain type, P type, U type, Z type, T type, H type, type, E type and Q type etc.. According to the use, it can be classified into buried rubber water stop belt and back sticking rubber water stop belt. The sealing material has good elasticity, abrasion resistance, aging resistance and tear resistance to deformation ability, good waterproof performance, temperature range of -45 DEG -+60 DEG. When the temperature exceeds 70 degrees Celsius, and the rubber sealing strip by strong oxidation or by oil and other organic solvent erosion, shall use the rubber sealing belt.
2使用方法
2 use method
橡膠止水帶必需采取可靠的固定措施，綁扎鋼筋和支模時。防止在澆注混凝土時發生位移，保證止水帶在混凝土中的正確位置。
The rubber sealing belt must take reliable fixed measures to bind the reinforcing bar and the support. Prevent the displacement of the concrete in the concrete and ensure the correct position of the water stop in the concrete.
只能在止水帶的允許部位上穿孔打洞，對于固定止水帶時。不得損壞止水帶有效防水部位。
Holes can only be perforated on the allowed parts of the water stop, for the fixed water stop belt. The effective waterproof part of the water belt shall not be damaged.
常用的固定方法有：利用附加鋼筋固定；專用卡具固定；用鉛絲和模板固定等。不論采用何種固定方法，對于止水帶的固定方法應按設計要求的施工規范進行且必需保證止水帶定位準確，不損壞止水帶有效防水部位，方便混凝土澆搗。
Fixed methods are commonly used: the use of additional reinforcement fixation; special fixture fixed with wire and fixed template. No matter what kind of fixation method is adopted, the fixing method of the waterstop should be carried out according to the construction specification of the design requirement, and the location of the sealing belt must be ensured accurately, and the effective waterproof part of the water stop zone is not damaged, so as to facilitate the concrete pouring and tamping.
3分類
3 Classification
按型號可分為：CB型橡膠止水帶（埋入式中間有孔型）；CP型橡膠止水帶（埋入式中間無孔型）；EB型橡膠止水帶（外貼式中間有孔型）；EP型橡膠止水帶（外貼式中間無孔型）。
According to the type, it can be divided into: CB type rubber water stop (embedded intermediate pass), CP type rubber water stop (buried intermediate no pass), EB type rubber water stop (externally attached middle pass), EP type rubber water stop (externally attached middle pass).
按材質可分為：天然橡膠止水帶，氯丁橡膠止水帶，三元乙丙橡膠止水帶。
According to the material, it can be divided into natural rubber water stop belt, chloroprene rubber water stop belt, three ethylene propylene rubber water stop belt.
按使用情況可分為：中埋式橡膠止水帶和背貼式橡膠止水帶(外貼式橡膠止水帶)、鋼邊橡膠止水帶、遇水膨脹橡膠止水帶、平板式止水帶。
According to the usage, it can be divided into: the buried rubber water stop and the back type rubber water stop (externally attached rubber water stop), the steel side rubber water stop belt, the water swelling rubber water stop belt and the flat type water stop belt.
4適用范圍
4 scope of application
橡膠止水帶主要用于混凝土現澆時設在施工縫及變形縫內與混凝土結構成為一體的基礎工程，如地下設施、隧道涵洞、輸水渡槽、攔水壩、貯液構筑物等。
The rubber sealing belt is mainly used for cast-in-place concrete when in construction joints and deformation joints and concrete structure has become one of the basic engineering facilities, such as underground tunnels, culverts, dams, aqueducts, liquid storage structures etc..
遇水膨脹橡膠止水帶主要用于混凝土現澆時設在施工縫及變形縫內與混凝土結構成為一體的基工程，如地下設施、隧道涵洞、輸水渡槽、攔水壩、貯液構筑物等。
The rubber sealing belt is mainly used for cast-in-place concrete when in construction joints and deformation joints and concrete structure has become one of the basic project of water swelling, such as underground facilities, tunnel, culvert aqueduct, dam, reservoir structures etc..
5施工安裝
5 construction and installation
止水帶是在混凝土澆注過程式中部分或全部澆埋在混凝土中。
The water stop zone is partially or completely buried in the concrete in the concrete pouring process.
