材料名稱：合金工具鋼
牌號：9SiCr
標準：GB/T 1299—2000
交貨狀態：熱軋、冷軋(退火)
交貨規格：熱軋2.5~6.0mm（板），冷軋1.5~2.5mm（帶）
特性及應用:
高碳合金工具鋼，韌性較好，具有較好的回火穩定性，熱處理時變形小。該鋼中碳化物分布均勻，不易析出碳化物網，并易于正火消除，通過正火可以消除網狀以及粗片碳化物組織。但是抗壓強度和耐磨性不足，加工性較差。該鋼的表面殘余含碳量為0.6%—0.7%的脫碳層時，由于碳化物的減少使得表面層的過熱敏感性增大。經正常加熱淬火以后表面硬度仍可以達到60—62HRC，但其抗彎強度卻下降40%—50%。表面層晶粒度達到7級，心部為10級。
該鋼鍛造性能良好，由于易脫碳，需要在中性氣氛或者保護氣氛爐中加熱。施以鍛熱調質處理，可以獲得細密的回火索氏體組織，簡化工藝，省時節電，既有良好的切削加工性能，又有理想的余熱處理組織。
該鋼受熱軟化溫度為320℃，淬透性比鉻鋼好，油淬淬硬性深度40—50mm。該鋼零保溫淬火韌化工藝，可以消除搓絲=板因常規淬火加熱氧化脫碳造成的早期失效，不均勻奧氏體修或可以細化馬氏體，搓火后得到隱晶馬氏體或者細針狀馬氏體，這種組織強韌性好。
9SiCr量具刃具用鋼，是常用的低合金工具鋼，具有較高的淬透性和淬硬性，以及較高的回火穩定性。
二 更多運用舉例：
1 該鋼用作沖制料厚≥3mm的沖裁模具中形狀復雜的凸模 凹模 鑲塊,做凸模時建議硬度58—62HRC，做凹模是建議60—64HRC。
2批量軟料中厚板沖裁模常用9SiCr等鋼。
3 用于滾絲模好，經超細化預處理后，服役期壽命提高一倍，
4 該鋼制M50×2搓絲板采用鍛熱調質預處理索氏體組織與淬火馬氏體比較接近，加之“薄殼淬火”，壽命提高2—3倍。
5 載荷輕或者小批量生產用冷鐓模
6 該鋼用于較精密復雜的模具。
7 該鋼用于下料模，沖頭，壓花模。
8 用于高強度的冷作模具鋼。
9 用于鋁件冷擠壓模，做凸模時建議硬度為60—62HRC。
10 齒輪沖模，剪刀以及冷軋錕。
11 是各種沖剪工具精壓膜，冷鐓模的基本材料。
12 適用用耐磨性高切削不劇烈且變形小刀具，如板牙 絲錐 鉆頭 鉸刀 齒輪銑刀 拉刀等。
應用：
9SiCr合金工具鋼可用于制造形狀復雜、變形小、耐磨性高、低速切削的工具，如鉆頭、螺紋工具、鉸刀、板牙、絲錐、搓絲板和滾絲輪等。（塑料模具鋼時，可用于頂出桿，制造尺寸家大，形狀復雜和精度要求高的塑料膜。
Material name: alloy tool steel
Brand: 9SiCr
Standard: GB/T 1299 - 2000
Delivery status: hot rolling, cold rolling (annealing)
Delivery specifications: hot rolled 2.5~6.0mm (plate), cold rolled 1.5~2.5mm (band)
Characteristics and applications:
High carbon alloy tool steel, toughness is good, with good tempering stability, heat treatment deformation is small. The steel carbide distribution, not to the precipitation of carbide network and easy to be normalized to eliminate, by normalizing can remove the mesh and plate coarse carbides. However, the compressive strength and wear resistance, poor processing. The steel surface residual carbon content of 0.6%, 0.7% of the decarburized layer, due to the carbide due to the decrease of surface layer of overheating sensitivity increases. The surface hardness can reach 60 to 62HRC after the normal heating and quenching, but the bending strength is decreased by 40% - 50%. The grain size of the surface layer reaches 7, and the heart is 10.
The good performance of steel forging, due to decarburization, need to be heated in a neutral atmosphere or protective atmosphere furnace. Impose forging heat quenching and tempering treatment can obtain fine tempered sorbite martensite structure, simplify the process, saving the electricity, both good cutting performance, and ideal heat treatment microstructure.
The steel heat softening temperature of 320 DEG C, the hardenability of steel ratio, oil quenching hardening depth of 40 - 50mm. The steel zero time holding quenching toughening technique, can eliminate rub silk = plate for conventional quenching heating oxidation and decarbonization cause early failure, inhomogeneous austenite or martensite refinement can, rub fire after cryptocrystalline martensite or fine acicular martensite body, the strong organization good toughness.
Steel 9SiCr measuring and cutting tools, commonly used low alloy tool steel with high hardenability and hardenability and high tempering stability.
Two more use of examples:
1 the steel used for punching material thickness of 3 mm rushed in the die cutting shape complex convex concave die die insert block, punch recommended hardness of 58 - 62 HRC, concave die is 60 - 64hrc recommendations.
2 bulk soft material in the thick plate blanking die commonly used 9SiCr steel.
3. The service life of the wire is improved, and the service life of the die is increased by the super fine,
4 the steel M50 * 2 rub silk plate by quenching and tempering heat forging pretreatment cable is very close to the martensite structure and quenched martensite, coupled with "shell hardening", life expectancy increased 2 - 3 times.
With the cold die 5 load light or small batch production
6 the steel is used for more precise and complicated mould.
7 of the steel used for blanking die, punch, die embossing.
8 for high strength cold work die steel.
9 for cold extrusion die for aluminum parts, the proposed hardness is 60 - 62HRC.
The 10 gear die, scissors and cold rolling roll.
11 is the basic material of fine punching tool lamination, cold heading die.
12 for high wear resistance of cutting intensity and deformation is small tool, such as die tap drill reamer broach and other gear cutter.
Application:
9SiCr alloy tool steel can be used in the manufacture of complex shape, small deformation, high wear resistance, low speed cutting tools, such as bit, thread tools, reamer and dies, tap, rub silk plate and screw rolling wheel etc.. Plastic mold steel, can be used for the top of the rod, manufacturing size, shape, complex and high accuracy requirements of plastic film.
