家家通 | 所有行業 | 所有企業 加入家家通,生意很輕松! ·免費注冊 ·登陸家家通 ·設為首頁
關于我們
關于我們
今日加盟
今日加盟
會員中心
會員中心
 
當前位置: 首頁 » 供應產品 » 閥門 » 氣動閥門 »客戶放心使用的上海VT雙作用氣缸

客戶放心使用的上海VT雙作用氣缸

<%=cpname%>
產品價格: 1000/人民幣 
最后更新: 2015-02-10 15:10:27
產品產地: 閔行經濟開發區
發貨地: 閔行經濟開發區 (發貨期:當天內發貨)
供應數量: 不限
有效期: 長期有效
最少起訂: 1
瀏覽次數: 212
詢價  試用會員產品
  • 公司基本資料信息
    • 上海法登閥門有限公司
    • 王君小姐 銷售
    • 會員[試用會員產品]
    • 郵件382295762@qq.com
    • 手機13061902132
    • 電話
    • 傳真
    • 地址上海市閔行區銀康路160弄30號12層
    • 進入商鋪
     
    產品詳細說明
    VATTEN® ACTUATOR OPERATION
    NOTE: For optimal operation, VATTEN actuators should be run with a supply of clean, lubricated air.
    SPRING RETURN ACTUATORS
    Air to PORT 2 (the right hand port) causes the actuator to turn CCW. Loss of air to PORT 2 causes air to
    exhaust and the actuator turns CW. This is the FAIL CLOSE operation.
    DOUBLE ACTING ACTUATORS
    Air to PORT 2 (the right hand port) causes the actuator to turn CCW. Air to PORT 1 (the left hand port)
    causes the actuator to turn CW.
    DISASSEMBLING STANDARD ACTUATORS
    IMPORTANT: Before beginning disassembly, ensure that the air supply to the actuator has been disconnected, all
    accessories have been removed and that the actuator has been dismounted from the valve.
    1. Loosen the end cap fasteners (22) with a wrench (size varies depending on actuator model). On the spring return
    actuator, alternate 3 to 5 turns on each fastener until the springs are completely decompressed. Use caution in
    removing the cap since the springs are under load until the fasteners are fully extended.
    2. Remove the pinion snap ring (10) with a lock ring tool. The indicator (7) may now be removed.
    3. Turn the pinion shaft (2) CCW until the pistons are at the full end of travel. Disengage the pistons (11) from the
    pinion. (NOTE: Low pressure air--3 to 5 P.S.I. MAXIMUM--might be required to force the pistons completely
    from the body.) Note the position of the pistons before removing them from the actuator body. The part numbers
    of the pistons are located on the side and should be right-side up on an actuator with a standard orientation.
    4. Remove the pinion through the bottom of the actuator. The actuator is now completely disassembled. All
    replacement parts may now be put in. VATTEN recommends that all wear parts (3, 4, 5, 6, 12, 13, 14) be
    replaced before reassembly.
    REASSEMBLING STANDARD ACTUATORS
    IMPORTANT: Be sure that the actuator surfaces are free of grit and scratches before reassembling.
    1. Apply a light film of grease to all o-rings and the pinion before replacing.
    2. Put the pinion (2) back through the actuator with the flats of the pinion shaft running parallel with the body.
    3. When reassembling the actuator, make sure that the piston racks are square to the actuator body and returned to
    their original orientation. (NOTE: The normal operation of all VATTEN actuators is FAIL CLOSED. If you want
    to change the orientation to FAIL OPEN, rotate the racks 180º to create a reverse operation.
    4. When replacing springs in a spring return actuator, ensure that the springs are replaced in their identical position
    in the end cap from which they were removed. (NOTE: In some circumstances, you might want to change the
    standard 80 pound spring set to fit your application and available air pressure. Changing the spring sets on
    VATTEN actuators requires no special tools. Please refer to the spring combination torque chart in our catalog
    for the inner and outer spring combinations that will allow you to operate with the spring set that you desire.
    5. Seal the end caps with a petroleum lubricant and bolt to actuator body.
    6. Check the seal of the actuator by covering seal areas (pinion, end caps) with soapy water and using low pressure
    air to the actuator to ensure that no bubbles are produced.

    在線詢盤/留言 請仔細填寫準確及時的聯系到你!
    您的姓名: * 預計需求數量: *    
    聯系手機: * 移動電話或傳真:
    電子郵件: * 所在單位:
    咨詢內容:
    *
     
    更多..本企業其它產品

    機電之家網 - 機電行業權威網絡宣傳媒體

    Copyright 2025 jdzj.com All Rights Reserved??技術支持:機電之家 服務熱線:0571-87774297

    網站經營許可證:浙B2-20080178-4

    主站蜘蛛池模板: 激情亚洲的在线观看| 色悠久久久久久久综合网伊人 | 欧美日韩一级片在线观看| 免费看大黄高清网站视频在线| 色噜噜狠狠一区二区三区果冻| 国产成人久久综合热| h视频在线观看免费网站| 国产美女高清**毛片| 99精品国产在热久久无毒不卡| 好男人看片在线视频观看免费观看| 中文字幕制服诱惑| 日日碰狠狠添天天爽不卡| 久久天天躁狠狠躁夜夜| 李丽珍蜜桃成熟时电影在线播放观看| 亚洲成a人片在线观看中文动漫| 法国女人与动zozoz0z0| 人人添人人妻人人爽夜欢视AV| 粉色视频免费入口| 午夜爽爽爽男女免费观看hd| 美妇又紧又嫩又多水好爽| 国产zzjjzzjj视频全免费| 露脸国语对白视频| 国产免费啪嗒啪嗒视频看看| 国产美女在线一区二区三区| 国产毛片久久久久久国产毛片| 手机在线看片国产| 国产精品亚洲成在人线| 18日本xxxxxxxxx视频| 国产精品永久久久久久久久久| 91无套极品外围在线播放| 国产馆手机在线观看| 99久久无码一区人妻| 在线电影一区二区三区| 99精品国产在热久久无码| 夜夜躁狠去2021| 99久久婷婷国产综合精品| 国内精品福利在线视频| 91蝌蚪在线播放| 国产精品美女久久久| 男女抽搐动态图| 国产熟女一区二区三区五月婷 |