家家通 | 所有行業 | 所有企業 加入家家通,生意很輕松! ·免費注冊 ·登陸家家通 ·設為首頁
關于我們
關于我們
今日加盟
今日加盟
會員中心
會員中心
 
當前位置: 首頁 » 供應產品 » 閥門 » 氣動閥門 »上海著名廠家生產德國品牌氣缸

上海著名廠家生產德國品牌氣缸

<%=cpname%>
產品價格: 1000/人民幣 
最后更新: 2015-02-06 15:54:35
產品產地: 閔行經濟開發區
發貨地: 閔行經濟開發區 (發貨期:當天內發貨)
供應數量: 不限
有效期: 長期有效
最少起訂: 1
瀏覽次數: 218
詢價  試用會員產品
  • 公司基本資料信息
    • 上海法登閥門有限公司
    • 王君小姐 銷售
    • 會員[試用會員產品]
    • 郵件382295762@qq.com
    • 手機13061902132
    • 電話
    • 傳真
    • 地址上海市閔行區銀康路160弄30號12層
    • 進入商鋪
     
    產品詳細說明
    Maintenance & Operating Instructions
    VATTEN® ACTUATOR OPERATION
    NOTE: For optimal operation, VATTEN actuators should be run with a supply of clean, lubricated air.
    SPRING RETURN ACTUATORS
    Air to PORT 2 (the right hand port) causes the actuator to turn CCW. Loss of air to PORT 2 causes air to
    exhaust and the actuator turns CW. This is the FAIL CLOSE operation.
    DOUBLE ACTING ACTUATORS
    Air to PORT 2 (the right hand port) causes the actuator to turn CCW. Air to PORT 1 (the left hand port)
    causes the actuator to turn CW.
    DISASSEMBLING STANDARD ACTUATORS
    IMPORTANT: Before beginning disassembly, ensure that the air supply to the actuator has been disconnected, all
    accessories have been removed and that the actuator has been dismounted from the valve.
    1. Loosen the end cap fasteners (22) with a wrench (size varies depending on actuator model). On the spring return
    actuator, alternate 3 to 5 turns on each fastener until the springs are completely decompressed. Use caution in
    removing the cap since the springs are under load until the fasteners are fully extended.
    2. Remove the pinion snap ring (10) with a lock ring tool. The indicator (7) may now be removed.
    3. Turn the pinion shaft (2) CCW until the pistons are at the full end of travel. Disengage the pistons (11) from the
    pinion. (NOTE: Low pressure air--3 to 5 P.S.I. MAXIMUM--might be required to force the pistons completely
    from the body.) Note the position of the pistons before removing them from the actuator body. The part numbers
    of the pistons are located on the side and should be right-side up on an actuator with a standard orientation.
    4. Remove the pinion through the bottom of the actuator. The actuator is now completely disassembled. All
    replacement parts may now be put in. VATTEN recommends that all wear parts (3, 4, 5, 6, 12, 13, 14) be
    replaced before reassembly.
    REASSEMBLING STANDARD ACTUATORS
    IMPORTANT: Be sure that the actuator surfaces are free of grit and scratches before reassembling.
    1. Apply a light film of grease to all o-rings and the pinion before replacing.
    2. Put the pinion (2) back through the actuator with the flats of the pinion shaft running parallel with the body.
    3. When reassembling the actuator, make sure that the piston racks are square to the actuator body and returned to
    their original orientation. (NOTE: The normal operation of all VATTEN actuators is FAIL CLOSED. If you want
    to change the orientation to FAIL OPEN, rotate the racks 180º to create a reverse operation.
    4. When replacing springs in a spring return actuator, ensure that the springs are replaced in their identical position
    in the end cap from which they were removed. (NOTE: In some circumstances, you might want to change the
    standard 80 pound spring set to fit your application and available air pressure. Changing the spring sets on
    VATTEN actuators requires no special tools. Please refer to the spring combination torque chart in our catalog
    for the inner and outer spring combinations that will allow you to operate with the spring set that you desire.
    5. Seal the end caps with a petroleum lubricant and bolt to actuator body.
    6. Check the seal of the actuator by covering seal areas (pinion, end caps) with soapy water and using low pressure
    air to the actuator to ensure that no bubbles are produced.

    在線詢盤/留言 請仔細填寫準確及時的聯系到你!
    您的姓名: * 預計需求數量: *    
    聯系手機: * 移動電話或傳真:
    電子郵件: * 所在單位:
    咨詢內容:
    *
     
    更多..本企業其它產品

    機電之家網 - 機電行業權威網絡宣傳媒體

    Copyright 2025 jdzj.com All Rights Reserved??技術支持:機電之家 服務熱線:0571-87774297

    網站經營許可證:浙B2-20080178-4

    主站蜘蛛池模板: 国产精品日韩欧美一区二区三区| 日本www高清| 亚洲精品线在线观看| 红颜免费观看动漫完整版| 国产亚洲美女精品久久久| 久久伊人色综合| 国产精品视频久久| 亚洲欧洲日产韩国在线| 男性玩尿眼玩法| 又爽又黄又无遮挡的视频在线观看| 超薄肉色丝袜一区二区| 国产无av码在线观看| jizzjizz之xxxx18| 忘忧草www日本| 亚洲av无码一区二区乱孑伦as | 国内一级一级毛片a免费| www.国产成人| 日韩欧美中文字幕在线观看| 伊人久久大香线蕉综合影| 精品欧美一区二区三区在线观看 | 波多野结衣痴女系列88| 免费v片在线看| 窝窝女人体国产午夜视频| 午夜影放免费观看| 美女的胸www又黄的网站| 国产va免费精品观看精品| 蜜臀AV一区二区| 国产在线不卡一区二区三区| 国产叼嘿久久精品久久| 国产真人无码作爱免费视频| 一二三四在线观看高清| 成人午夜私人影院入口| 亚洲av永久无码精品天堂久久| 欧美日韩国产网站| 亚洲欧美另类日韩| 欧美综合第一页| 亚洲欧美一区二区三区图片| 欧美精品v欧洲精品| 亚洲欧洲校园自拍都市| 欧美日韩国产片| 亚洲国产婷婷综合在线精品|